Porsche 928S 1983 Driver Manual Download Page 11

Page: 11 / 110

Doors

The doors are opened from the outside by

pulling the inset door handle, and from
inside, by pulling lever (C).

Access to the storage compartments in the
door is obtained by pressing the safety

knob, and tipping the armrest outwards.

The window regulators are operated by the

rocker switches in the middle console.

Warning: To avoid injury to unknowing occu-

pants of the vehicle, (e. g. children) by the
closing of the windows, the ignition key
should always be withdrawn when leaving

the vehicle, if only for a short period.

The footwell lights (D) mounted forward in
the lower part of the door trimcone on, with
the switch in the appropriate position, when
the door or the luggage compartment door

is opened. Each light can also be switched

on or off individually by means of the inte-
grated switch.

Central door locking

By means of the central door locking system
both doors are electrically locked or unlock-

ed by operating one lock.

When the doors are locked the locking but-
tons (A) must be fully retracted. If this is not
the case the lock on that door is not properly

engaged. Re-open the door, close it pro-
perly and re-lock it.

Summary of Contents for 928S 1983















































































































Search results

Summary of Contents for 928S 1983

Reviews:

Brands by name

Popular brands

Porsche 928S 1983, Driver Manual

Search results

Summary of Contents for 928S 1983

Reviews:

Brands by name

Popular brands