Porsche 928S 1983 Driver Manual Download Page 80

Page: 80 / 110

Auxiliary driving lamps

1. Remove screws from lamp surround and

remove surround.

2. Remove the lamp fixing screws (see

arrows) and pull out the complete lamp.

3. Remove cable socket and bulb retaining

spring. Refit new bulb ensuring that it sits
properly.

4. Refit bulb retaining spring and cable

socket.

5. Refit the lamp and the fixing screws.

Check that the lamp functions and that it

is properly adjusted.

Front side light

Front blinker light

The front side light is built into the outer auxi-

liary driving lamp.

1. Remove complete lamp, and then the

sidelight bulbholder.

2. Refit new bulb and replace lamp.
3. Check function of light.

1. Remove screws holding the lens, and

remove lens.

2. Remove bulb from bulbholder, and fit new

bulb.

3. Replace lens, and refit screws, tightening

gradually in sequence.

4. Check function of light.

Summary of Contents for 928S 1983















































































































Search results

Summary of Contents for 928S 1983

Reviews:

Brands by name

Popular brands

Porsche 928S 1983, Driver Manual

Search results

Summary of Contents for 928S 1983

Reviews:

Brands by name

Popular brands