Ponpe 8351 Operation Manual Download Page 21 | Manualshive

Page: 21 / 30

Ponpe 8351 Operation Manual Download Page 21

MAINTENANCE

Make sure the electrode is clean!
Between measurements, rinse the
electrode with deionised water. If
the eletrode has been exposed to
a solvent immiscible with water,
clean it with a solvent miscible with

water e.g. Ethanol and rinse carefully
with water.

Store the electrode carefully! Before
storing, rinse it carefully in deionised
water and store

dry

.

Power on but no display

TROUBLESHOOTING

1) Make sure the time of pressing
power key is more than 100 mS.
2) Check the battery are in place and
make good contact and correct
polarity.
3) Replace with new batteries and try
again.
4) Move away the batteries for one
minute and then put back again.

Check whether the low battery icon
is appeared before the display is off.
If yes, replace with new batteries.

Display disappear

20

The air bubbles are easy to adhere
around the gap between electrode
and meter. Under this situation, the
accuracy will be quite poor.

Air bubbles adhere on electrode

«
...
19
20
21
22
23
...
»

Summary of Contents for 8351































Reviews:

No comments