background image

WAT E R G A R D E N I N G   T O   T H E   M A X

WAT E R G A R D E N I N G   T O   T H E   M A X

COLOR CHANGING LED 

LIGHTING SYSTEM

ADD-ON LIGHT

The Add- n Lights are perfect for extending your light

 system.  The Add-On light comes with a 9Ft underwater 

cable  to connect directly to your Starter Light or other Add-On Lights. Similar to the Starter light these lights also 
include an underwater daisy chain connector on the side of the fixture, to continue the sequence on. 

Add-On 

ight  

 with RF 

emote ransformer

.

uitable for outdoor use only. 

DO NOT use in water intended for swimming, 

wading, immersion, or bathing.

DO NOT tamper with the light cable or connectors, 

as this can result in injury and will void the warranty.

INSTALLATION

• Install your light in the desired place in your landscape or water feature. 
• Run the cable back to the previous light in the chain. 
• Connect your light cable connector to the daisy chain connector on the side of the previous light and tighten the 

plastic nut to ensure a safe connection. 

• Bury the cable 6” below the surface to protect it from damage. Avoid damage to the cable from knives, shovels and 

stones. 

• Finally tighten the cap on the electrical connector on the side of the light to prevent leaking and a short circuit.

MAINTENANCE

• Follow the maintenance procedures as noted for the Starter ght

8

Summary of Contents for 24PL680

















Reviews: