background image

 

110-509 PSC/EN 

Regulatory Compliance and Testing 

This equipment is compliant with the European Directive 2002/95/EC and its latest amendments on 
Restrictions on Hazardous Substances (RoHS) and below the given limits of hazardous substances. 

ETL Intertek (60 Hz units) 

UL 61010-1 / CSA C22.2 No. 61010-1 — Safety Requirements for Measurement, Control, and 
Laboratory Use; Part 1: General Requirements 

UL 61010A-2-010 / CSA C22.2 No. 61010-2-010:04 — Safety Requirements for Measurement, Control, 
and Laboratory Use; Part 2-010: Particular Requirements for Laboratory Equipment for the Heating of 
Materials 

UL 61010A-2-051 / CSA C22.2 No. 61010-2-051:04 — Safety Requirements for Measurement, Control, 
and Laboratory Use; Part 2-051: Particular Requirements for Laboratory Equipment for the Mixing and 
Stirring 

CE (all units) 

EC Low Voltage Directive 2006/95/EC 

EC Electromagnetic Compatibility Directive 2004/108/EC 

IEC 61010-1-2001 

IEC 61010-2-2001 

IEC 61326:2005 / EN 61326 : 2006 

 

Unpacking Your Circulator  

Your Circulator is packed in a special carton or cartons. You should keep the packaging, along with all 
packing materials, until the unit has been installed and you are certain it is working properly.  

 

CAUTION:

 Remove any loose packing material that may have fallen into the heater/pump housing 

during shipping. Before powering up, check that nothing remains around the heater or Circulator 
pump. 

We recommend that you begin using your Circulator immediately to confirm proper operation, since 
beyond one week you may be eligible for warranty repair only (rather than replacement). You’ll find 
complete warranty information in the back of this manual. 

In the unlikely event that the unit was damaged or does not operate properly, immediately contact the 
transportation company, file a damage claim, and contact the company where your Circulator was 
purchased. 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for MX06S135












































Reviews: