background image

SpectraLink Corporation 

Link Wireless Telephones and Accessories User Guide 

Part Number: 72-0075-09-C.doc 

Page 10 

Link Wireless Telephone Accessories 

Battery Packs 

Overview 

The wireless telephone will need to have its Battery Pack (PTS360) 
recharged periodically. The Nickel Metal Hydride (NiMH) 
rechargeable wireless telephone Battery Pack gives you four hours 
of talk time or 80 hours of stand-by time. Stand-by time is when the 
phone is turned on, but you are not using it. 

Indications of low battery 

The wireless telephone will notify you when the charge on the 
Battery Pack becomes low. If the wireless telephone is in use, the 

BATT

 message will display and you will hear a soft beep through the 

earpiece every six seconds. You have two minutes to complete the 
call or change the Battery Pack. 
The Battery Pack can be changed while the call is still in progress. 
Do not press 

END

. Quickly remove the discharged Battery Pack 

and replace with a charged Battery Pack, press 

PWR

, and then press 

START

 to resume the call in progress. 

If the wireless telephone is idle, you will hear a brief modulated ring 
signal and the Low Battery message will display. Your wireless 
telephone will not operate until you replace the Battery Pack. 
Depending on the charging equipment you have purchased, you will 
either place the wireless telephone in a Charging Stand to charge the 
Battery Pack, or you will remove the Pack from the wireless 
telephone and install it in the Charger. 

Caution: 

Take care not to short the battery contacts on the Battery Pack with 
metal objects such as coins, keys or paper clips. Shorting the 
contacts can cause permanent damage. 

Battery Pack removal and 

replacement 

To remove the Battery Pack, press down on the oval button above 
the Battery Pack on the back of the wireless telephone. Slide the 
Pack toward the bottom of the wireless telephone until it stops, 
then lift up.  
To replace the Battery Pack, first properly align the top of the 
Battery Pack with the arrows on the label on the back of the 
wireless telephone. Gently press and slide the Pack toward the top 
of the wireless telephone until it snaps into place. You should not 
have to force it against the wireless telephone. 

Important

 

Only use SpectraLink Battery Packs with SpectraLink Wireless 
Telephones. 
Do not dip the Battery Pack in water or throw into fire. 
Do not throw away the Battery Pack with your domestic waste. 
Take used Battery Packs to an appropriate collection point for 
recycling or send them back to your supplier or servicing agent. 

 

Summary of Contents for SpectraLink BC4900


























Reviews: