Poly Pong CRUISE SHIP ALL-WEATHER Assembly Manual Download Page 7 | Manualshive

Page: 7 / 16

background image

Lower the beam-leg
assembly onto the table
tops assembly and
position it so that the
beam covers on each end
fit into the slots just inside
the front diagonal lip of
the table edge just above
the inverted POLY PONG
logo and centered on the
diagonal table edge. This
should be the same for
both sides Fig. 13 & 14.

Fig. 13

Fig. 14

PAGE 6

«
...
5
6
7
8
9
...
»

Summary of Contents for CRUISE SHIP ALL-WEATHER

















Reviews:

No comments

Related manuals for CRUISE SHIP ALL-WEATHER

Brand: Laser Pegs Pages: 2

Brand: Zippkits Pages: 26

IDF Merkava Mk.IV

Brand: Eduard Pages: 6

G2579 The Incredibles

Brand: Fisher-Price Pages: 10

Brand: WowWee Pages: 36

Fun 2 Learn J6870

Brand: Fisher-Price Pages: 8

Brand: Opale-Paramodels Pages: 6

Lincoln Logs Big L Ranch

Brand: K'Nex Pages: 8

Zoom Ju 87A interior S.A.

Brand: Eduard Pages: 4

Zoom Bf 109E-7 S.A.

Brand: Eduard Pages: 3

Brand: Black Horse Model Pages: 46

35cc EXTRA 300 ARF-QB

Brand: AeroWorks Pages: 80

The Harrison Dollhouse Kit

Brand: Greenleaf Pages: 4

BABY born Sister Styling Creative Head

Brand: Zapf Creation Pages: 28

Brand: Gyros Pages: 8

MARIO KART WII MARIO AND YOSHI FINISH LINE BUILDING SET

Brand: K'Nex Pages: 12

D9R Doobi cooling slats

Brand: Eduard Pages: 2

Historic Wings Fokker Spin 1912

Brand: Aircraft in Miniature Limited Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands