background image

 

POLITEC s.r.l. | Sandor Dual Sma manual – Ver. 2.4

7

 

4

 

CABLES AND WIRING 

 

The wiring requires to SEPARATE the power cable 12Vdc (ex. 2x0.5 + Nx0.22),to the power 
cable for heaters 24Vac (ex. 2x0.75) to prevent input of disorders of the AC voltage on the 
barrier.

 

N.B. is absolutely necessary to shield the cable that provides 12 Vdc power supply and put 
the metal braid to ground. 

 

The cable size depends on the consumption of the columns and the resistance of the cable to the distances 
involved. 
 
The table shows the cable sections and the relative distances to which they provide optimum performance using 
the supplier LAR22 (12Vdc - 2,5A / 24V AC-300W) and a barrier SANDOR DUAL SMA. 
 

Cable

 

section

 

12Vdc

 

24Vac

 

0,5 mm² 

165 m 

35 m 

0,75 mm² 

245 m 

50 m 

1,5 mm² 

490 m 

100 m 

2,5 mm² 

820 m 

165 m 

4 mm² 

1310 m 

265 m 

6 mm² 

1975 m 

400 m 

 

N.B. THE LAR22 IS NOT WATERPROOF, MUST BE PLACED INSIDE A LOCAL OR PLACED IN 
A SEALED CONTAINER FOR USE OUTSIDE. 
 

Is possible use the power supplier LAR18 (12Vdc – 0,9A / 24VAC-60W) to supply a single column.

 

 

 

Summary of Contents for SANDOR DUAL SMA

























Reviews: