3
PROGRAMMING TRANSMITTERS
To use the transmitter with your alarm/starter
system, you must first have the system
learn the
transmitter's code.
The system can learn a total of
4 transmitters. If more than 4 transmitters are
programmed, the oldest codes will be replaced.
(The same transmitter can be coded 4 times to lock
out all other transmitters.)
NOTE:
In order to program a new transmitter
code,
Alarm Valet Mode must be disabled
. Also,
when programming the transmitter, make sure that
no other transmitter is in use or the alarm/starter
unit may learn it. Start with the Valet switch in
OFF position.
1. Make sure that the
Alarm Valet Mode is
disabled
.
2. Turn the Ignition switch to ON.
3. Open the Hood.
4. Turn the Valet switch ON, OFF, ON.
5. The Parking lights will come ON. You have up
to 5 seconds to
press Lock button on the
transmitter
to be added to the unit, if the
operation is successful, the alarm/starter unit
will flash the Parking lights 5 times quickly.
*Another transmitter can be programmed at this
point by flipping the Valet OFF then back ON,
and press a button on the transmitter to be
learned.
(System can hold 4 transmitters in
memory.)
NOTE:
That the Alarm Valet Mode is enabled at
the end of this procedure. You should disable it to
return to normal operation.
MULTI CAR OPERATION
(Only available on
5503/5504/5505)
*To program transmitter to second
vehicle for multi-car operation, you must press
on the transmitters Trunk button in step 5 of
transmitter code learning.
The PS-5503/5504/5505/5514 systems feature
multi-car operation.
This allows the owner of two Polarstart systems in
two of his/her vehicles to control both systems with
one transmitter. (Both vehicles must be equipped
with an PS-5503/5504/5505/5514.
The remote transmitter of the primary vehicle can
control the starter disable system, the door locks
and the remote car starter operation of the second
vehicle.
The remote transmitter of the second vehicle can
also operate the primary vehicle.
REMOTE STARTER & ALARM VALET
MODES
The alarm/starter unit can be placed in
Remote
Starter Valet Mode
to disable
the capability of
starting the engine by remote
while maintaining
the alarm and door locking & unlocking
functions. This is recommended if the vehicle is
to be parked in a garage or if the vehicle needs to
be serviced.
The alarm/starter unit can also be switched to
Alarm Valet Mode
to stop an alarm condition or
to disable
the alarm functions
and the anti-theft
starter kill feature. While in the Alarm Valet
Mode, the remote starting capability, the panic
mode and door locking/unlocking functions are
still operational.
NOTE: Enabling Alarm Valet Mode is
required if you want to stop the initial alarm
condition that occurs when powering-up the
system.
ENABLING ALARM VALET MODE
1. Make sure the Ignition key is in the OFF
position.
2. Set the Valet switch to OFF.
3. Turn Ignition ON and wait for 2 sec.
4. Set the Valet switch to ON. At this point the
LED turns and stays ON
to indicate that the
Alarm Valet Mode is enabled.
5. Set the Valet switch and Ignition OFF.
DISABLING ALARM VALET MODE
1. Make sure the Ignition key is in the OFF
position.
2. Set the alarm Valet switch to ON.
3. Turn Ignition ON and wait for 2 sec.
4. Set the alarm Valet switch to OFF. At this
point the
LED turns and stays OFF
to
indicate that the Alarm Valet Mode is
disabled.
5. Turn Ignition OFF.
ENABLING STARTER VALET MODE
1. Make sure you did set the alarm Valet mode,
as you require.
2. Set
the
Valet switch ON*.
* ON = No Start
DISABLING STARTER VALET MODE
1. Make sure you did set the alarm Valet mode,
as you require
2. Set
the
Valet switch OFF*.
The remote starter is now in normal operation.
* OFF = Starter works
Summary of Contents for PS-5500
Page 9: ...9 ...
