Polaroid Originals Polaroid Lab, User Manual

Page: 17 / 91

User Manual
15
Safety Information
Caution
Risk of electric shock — Do not open/
Disassemble the motorized roller system
• Do not disassemble the device. Incorrect
reassembly can cause electrical shock if
the device is used again.
• Do not immerse the device in water or
other fluids.
• Do not operate the device in a high
humidity environment or very dusty
environments.
• Do not attempt to tamper with, adjust or
remove the battery and/or the electron-
ics located below the rollers behind the
device’s film door.
• Do not attempt to remove the door itself
as it is connected electronically to the
body of the device. Doing so is unsafe,
will likely damage your device, and will
void your warranty.
• Do not insert metal objects into the
device.
• Do not insert any objects into the rollers or
gears.
• Keep small children and infants away
from device to avoid them being injured
by the device’s moving parts.
• Do not use or store the device near any
heat source or any type of equipment
that generates heat, including stereo
amplifiers.
• Do not use the device near flammable or
explosive gases.
• Do not charge the device if you notice
any unusual odors, noise or smoke.
• Do not attempt to disassemble the film’s
battery or modify it in any way (if using
600-type film). If battery fluid gets in
your eyes, immediately rinse your eyes
with fresh, cold running water and seek
medical attention immediately.
Battery and Charger
• This device uses a custom lithium-ion
battery that is non-removable and
mounted inside the Lab body. No other
type of battery can be used. Battery
replacement can only be done by autho-
rized service centers. The battery will
provide many years of service if properly
used. Power consumption varies depend-
ing on the environment the device is used
in and how the device has been stored.
Used immediately after full charge, the
battery will power the processing of up to
30 film packs.
• Once the battery energy level falls below
a certain level, the device will no longer
process film. The LED will blink and signal
when it needs to be recharged. This is to
avoid a photo getting stuck as it is being
processed through the roller system.
• The rechargeable battery is not fully
charged at the time of purchase. Charge
the battery fully with the USB charging
cable (provided). This usually takes 1-2
hours (can vary depending on usage).
• The supplied battery charging cable
has been tested to work with the Apple
iPhone power adaptors. While it can be
used in other USB ports e.g. computer,
USB power adaptors, TVs, cars etc., cor-
rect operation cannot be guaranteed.
• When the device is no longer in use,
please recycle it properly.
Usage Environment
• To protect the high-precision technology
contained in this device, never leave the
Lab in the following environments for ex-
tended periods of time: high temperature
(+42°C/108°F), high humidity, places
with extreme changes in temperature
(hot and cold), direct sunlight, sandy or
dusty environments such as beaches,
damp places, or places with strong
vibrations.
• Do not drop the device or subject it to
severe shocks or vibrations.
• Do not push, pull or press on the lens
surface
Compliance
Important directions for using
Lithium–Ion Batteries
1. Do not throw into fire.
2. Do not short circuit.
3. Do not disassemble.
4. Do not continue to use when damaged.
5. Dispose correctly after use.
6. Keep away from water.
EU Declaration of Conformity
Hereby, Impossible B.V. declares that the
Polaroid Lab is in compliance with the es-
sential requirements of the Electromagnetic
Compatibility Directive (2014/30/EU), Low
Voltage Directive (2014/35/EU) and RoHs
Directive (2011/65/EU) and other relevant
provisions, when used for its intended
purpose.
FCC Compliance Statement
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
Caution The user is cautioned that
changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment. This equipment
must not be co-located or operated in
conjunction with any other antenna or
transmitter.
Note This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there
is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This equipment complies with fcc radiation
exposure limits set forth for an uncontrolled
environment. End user must follow the
specific operating instructions for satisfying
rf exposure compliance.
Industry Canada (IC)
This device complies with part 15 of the FCC
Rule and Industry Canada license–exempt
RSS standard(s). Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation. Le present
appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio
exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur d’appareil doit accepter
tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en comprom-
ettre le fonctionnement.
The symbol means that according to
local laws and regulations your prod-
uct should be disposed of separately
from household waste. When this product
reaches its end of life, take it to a collection
point designated by local authorities. Some
collection points accept products for free.
The separate collection and recycling of
your product at the time of disposal will
help conserve natural resources and ensure
that it is recycled in a manner that protects
human health and the environment.