Polaris RANGER XP 900 Owner'S Manual For Maintenance And Safety Download | Manualshive

Page: 113 / 147

background image

111

MAINTENANCE

Battery

Improperly connecting or disconnecting battery cables can result in an explosion
and cause serious injury or death. When removing the battery, always
disconnect the negative (black) cable first. When reinstalling the battery, always
connect the negative (black) cable last.

Your vehicle has a sealed battery, which requires little maintenance.
Always keep battery terminals and connections free of corrosion. If
cleaning is necessary, remove the corrosion with a stiff wire brush.
Wash with a solution of one tablespoon baking soda and one cup water.
Rinse well with tap water and dry off with clean shop towels. Coat the
terminals with dielectric grease or petroleum jelly.

Battery Removal

1. Remove the driver’s seat. See page 32.

2. Disconnect the black (negative) battery cable first.

3. Disconnect the red (positive) battery cable last.

4. Remove the battery hold-down strap.

5. Lift the battery out of the vehicle.

WARNING

«
...
111
112
113
114
115
...
»

Summary of Contents for RANGER XP 900




















































































































































Reviews:

No comments

Related manuals for RANGER XP 900

Brand: J&M Pages: 26

Brand: E-Z-GO Pages: 158

Brand: Polaris Pages: 309

ROXOR HDUV 2023

Brand: Mahindra Pages: 119

Brand: FLEMING Pages: 6

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Ventrac Pages: 93

Brand: Toro Pages: 32

Brand: Fisher-Price Pages: 28

Brand: Fisher-Price Pages: 40

Brand: Yamaha Pages: 42

Brand: Range Road Pages: 21

K2 QUAD 250 - SERVICE

Brand: GAS GAS Pages: 64

WOLVERINE YXE70WPXH

Brand: Yamaha Pages: 186

Brand: Yamaha Pages: 504

Brand: PARKIT360 Pages: 13

Brand: Toro Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands