background image

Page  9

 

|

 

Polaris

® 

AutoClear

® 

SC (PAGSC20K) Salt Chlorinator - Installation and Operation 

Manual

 

ENGLISH

 

 

Section 3. Installation

 

Instructions

 

 

  

WARNING

 

FOR YOUR SAFETY: 

This product must be serviced 

by a professional pool service technician as 
described on the front cover of this manual. The 
procedures in this manual must be followed exactly. 
Failure to follow warning notices and instructions may 
result in property damage, serious injury, or death.

 

Improper installation and/or operation may void the 
warranty.

 

EQUIPMENT UNDER PRESSURE: 

Always turn

 

pump off prior to installing or servicing the chlorine 
generating device. Your pump/filter system is 
operated under pressure and the pressure must be 
released before you begin work. Please see your 
pump/filter 

owner’s manual for further instructions.

 

   

WARNING

 

To reduce the risk of electric shock, do not use

 

extension cord to connect unit to electric supply; 
provide a properly located outlet.

 

   

WARNING

 

Risk of Electric Shock. Connect only to a branch

 

circuit protected by a ground-fault circuit-interrupter 
(GFCI). Contact a qualified electrician if you cannot 
verify that the circuit is protected by a GFCI.

 

   

CAUTION

 

To reduce the risk of electric shock do not place the

 

power pack closer than 3 metres (10 feet) from the 
pool.

 

Do not bury the cords. Locate cords to minimize 
abuse from lawn mowers, hedge trimmers, and other 
equipment.

 

Before you begin your installation, please check that 
you have the right tools and a suitable location to install 
the power pack and cell. Please ensure that you have 
read and understood the Important Safety Instructions 
section.

 

 

3.1 

Materials and Tools 

 

Installation Materials Furnished 

•  Pipe spacer - for 40 mm (1½ in.) pipe

 

•  Screw set (includes wall plugs)

 

•  Installation and Operation Manual

 

3.2 

Installation Requirements 

 

 

Figure 3. 

Installation Requirements

 

 

The installation requirements for the chlorine generating 
device are as follows:

 

•  The power pack must be installed at least 0.6 

m (2 ft.)  vertically off the ground.

 

•  The power pack must be be installed at least 3 

metres (10 feet) from the inside wall of your 
swimming pool 

 

•  The cell must be installed with the provided pipe

 

adapter.

 

•  The cell must be installed no more than 4.6 m (15 

ft.) from the power pack.

 

•  The power pack must be installed no more than

 

1 m (3 ft.) from an electrical outlet.

 

•  The flow pod must be installed upstream from the 

cell.

 

•  It is recommended that the flow switch and cell be 

installed 0.25 m (10 in.) from any 90° elbow.

 

WARNING

 

The chlorine generating device must be installed 
horizontally with the cell above the pipe to avoid 
buildup of flammable gases which can result in FIRE 
OR EXPLOSION.

 

It is required that the water flow pod is installed in the 

or diverters between them.

 

 

 
 
 

 

Power Pack

 

 
 
 

 

Cell

 

 
 
 
 

Pod

 

 
 
 
 

 

Flex Hose*

 

(*Not to scale)

 

Summary of Contents for AutoClear SC






























Reviews: