PLP BCH25 Operator'S Manual Download Page 9 | Manualshive

Page: 9 / 20

PLP BCH25 Operator'S Manual Download Page 9

Connecting Throttle Cable

1. With air cleaner cover removed, Put two cable

adjuster nuts (packed with Engine Box ) on the
end of throttle cable. Slip the throttle cable
through the slot in the slotted fitting, making sure
the cable lug drops into the recessed hole (See
sketch).

2. Position the throttle cable in the throttle cable

bracket fix it with tightening the two cable
adjuster nuts. Adjust the cable position to keep
1-2mm play between cable lug and slotted fitting
(See sketch).

3. Operate the throttle trigger a few times to make

sure that it works correctly. Check the stop on
the carburetor throttle cam just contacts the idle
speed adjustment screw when the throttle trigger
is fully depressed.

4. When the throttle cable is adjusted correctly,

tighten two adjuster nuts.

Connecting Stop Switch Wires

1. Plug the stop switch terminal A into the matching

connector from the engine.

2. Fix the stop switch terminal B to the engine body

with the screw (packed with Engine Box).

Installing Guard

Blade Guard

[BCH25, BCH25H]

Attach the blade guard to the gearcase with the four M5

×

12

screws as shown.

[BCH35, BCH35H]

Attach the blade guard to the gearcase with the two M6

×

30

screws as shown.

Trimmer Head Guard

(Install the nylon line cut off blade and guard extension to the
blade guard.)
1. Fasten the nylon line cut off blade to the blade guard with

two M5

×

25 screws, lock washers and hex nuts as shown.

2. Attach the guard extension to the blade guard with the five

M5

×

15 screws, washers and hex nuts as shown.



WARNING

POTENTIAL HAZARD

・

Foreign objects can be thrown by Trimmer/Brushcutter.

WHAT CAN HAPPEN

・

Contact with thrown objects can cause personal injury.

HOW TO AVOID THE HAZARD

・

Never operate the Trimmer/Brushcutter without the

blade guard.

─

6

─

Recessed Hole

Cable Lug

Slotted Fitting

1- 2mm
Play

Screw

Cable adjuster
nuts

Terminal B

Throttle Cable

Terminal A

Throttle Cable
Bracket

Gearcase

Blade Guard

M5

×

12 Screw(4)

Gearcase

Blade Guard

M6

×

30 Screw(2)

[BCH25, BCH25H]

[BCH35, BCH35H]

Blade Guard

Guard Extension

M5

×

25

Screw(2)

String Cutoff
Blade

M5

×

15

Screw(5)

washer (5)

Lock
washer (2)

Hex Nut (5)

Hex Nut (2)

«
...
7
8
9
10
11
...
»

Summary of Contents for BCH25





















Reviews:

No comments