pleasant hearth PH35PS-B Owner'S Manual Download Page 32

Page: 32 / 44

7077-801F • 08/20

F. Through The Wall

Horizontal termination cap must be a minimum of 6

inches. (152mm) from the wall. Approved for mobile home

installations. Must use 3 or 4 inch (76-102mm) “L” or “PL”

listed pellet venting or Listed double wall pipe and an

authorized Outside Air Kit in mobile homes.

NOTE:

In Canada, where passage through a wall or

partition of combustible construction is desired, the

installation shall conform to

CAN/CSA-B365

NOTICE:

Please note that while the minimum clearance

for the termination cap is 6 inches (152mm) there is the

possibly of soot build-up around the termination area. If

this occurs we suggest to move the termination further

away from the house to prevent it. The suggested

minimum is 12 inches.

DO NOT DOWNWARD VENT.

The following will occur:

•

The appliance will not vent properly

•

Smoke spillage in the house

•

Excessive sooting

CAUTION

6 in.

(152mm)

Minimum

Non-combustible Hearth Pad

Wall

Thimble

Horizontal

Termination

Cap

2 in.

(50.8mm)

Minimum

6 in.

(152mm)

Minimum

From Glass

Straight Out

Wall

Thimble

Illustration shows venting going in both directions.

Choose which one is best for your installation.

3 in. (76mm)

Minimum

3 in.

(76mm)

Minimum

6 in (152mm) Minimum

6 in (152mm)

Minimum

45 Degrees

Summary of Contents for PH35PS-B













































Search results

Summary of Contents for PH35PS-B

Reviews:

Related manuals for PH35PS-B

Brands by name

Popular brands

pleasant hearth PH35PS-B, Owner'S Manual

Search results

Summary of Contents for PH35PS-B

Reviews:

Related manuals for PH35PS-B

Brands by name

Popular brands