manualshive.com logo in svg

Playcore Spectrum Aquatics Motion Trek 350, Manual

Share
Download
Playcore Spectrum Aquatics Motion Trek 350 Manual Download Page 12

11 

800.791.8056 

▪ www.spectrumproducts.com 

Troubleshooting 

Problem: 

Cause: 

Solution: 

1. Lift will not operate at all: 

Low Battery (Lift) 

– Red or 

amber LED on the receiver 

 

Recharge Battery 

 

2. The seat will not raise or lower. 

The seat will not rotate. 

Low battery  

Battery not installed 
properly 

Receiver malfunction 

Recharge battery 

Reinstall battery 

Replace Receiver* 

 

3. The seat’s motion isn’t smooth 
or sticks at a certain point during 
travel. 

Excessive wear to bearings 

Excessive wear to Actuator 

Replace bearings* 

Replace Actuator* 

4. The seat travels much slower 
than normal. 

Low battery 

 

Recharge battery 

 

5. The lift makes much more noise 
or unusual noises during operation. 

Excessive wear to bearings 

Pivot points galling  

Replace bearings* 

Oil pivots with light oil 
(3-1) 

6. Battery will not charge: 

Bad Battery (red LED on 
charger 

– not turning 

orange or green in 4 hours 
or less) 

 

Replace Battery* 

*Please contact your local distributor or Spectrum Customer Service to order parts 406.532.6321

 

Summary of Contents for Spectrum Aquatics Motion Trek 350













Reviews:

No comments

Brands by name

Popular brands

Load more brands