manualshive.com logo in svg

Playcore Spectrum Aquatics Motion Trek 350, Manual

Share
Download
Playcore Spectrum Aquatics Motion Trek 350 Manual Download Page 10

9 

800.791.8056 

▪ www.spectrumproducts.com 

Rotation (CLOCKWISE) 

: 

Pressing the 

 button causes the lift to rotate clockwise. The lift will continue to rotate in this 

direction as long as the button is pressed. Releasing the button at any time during rotation will 
stop the lift from rotating. 

Rotation (COUNTERCLOCKWISE) 

: 

Pressing the 

 button causes the lift to rotate counterclockwise. The lift will continue to rotate 

in this direction as long as the button is pressed. Releasing the button at any time during 
rotation will stop the lift from rotating. 

To enter the Pool or Spa: 

A.  Position the chair of the lift over the deck in a suitable position for a transfer using 

the directional buttons on the transmitter 

B.  Carefully transfer into the lift seat from mobility device 
C.  Fasten seatbelt 
D.  Rotate the lift over the water, where it will not come into contact with the pool edge 

or any obstruction using the left or right buttons on the transmitter 

E.  Lower the lift into the water until buoyant, by pushing the down button 
F.  Unfasten seatbelt and carefully move away from the lift 
G.  Using the directional buttons on remote return lift chair to an on deck position not 

over the pool 

To Exit the Pool or Spa: 

A.  Recall lift chair into water to the previous depth and position upon transferring from 

the lift seat to the pool using directional arrows 

B.  Carefully transfer into the lift seat from water 
C.  Fasten seatbelt 
D.  Lift the seat straight up using the up directional arrow on the transmitter until top of 

lifting stroke is reached 

E.  Rotate the chair into a suitable position on deck to transfer from lift seat 
F.  Unfasten Seatbelt 
G.  Carefully Transfer from lift seat into mobility device 

Battery Charging & Installation 

The battery comes partially charged, but will need charging after the first several hours of use.  
Charging time is approximately twelve hours for the first few charges, four hours after the first 
two full battery cycles at which point the battery will reach maximum capacity.  The lift comes 
with a battery charger for use in dry locations.  Charge the battery as follows: 

Plug the battery charger into a standard* outlet.  The green LED on the charger will light up, 
indicating that the charger is on.  

Plug the charging cable into the charging port on the battery cradle. Place battery in charging 
cradle. If the battery is up to the charged voltage, the LED on the charger will stay green. If the 

Summary of Contents for Spectrum Aquatics Motion Trek 350













Reviews:

No comments

Brands by name

Popular brands

Load more brands