Plantronics Poly Medialign 65 Installation Manual Download

Page: 56 / 157

Setting Up the Poly Medialign Single Display System

Poly, Inc.

Place the camera / bracket assembly on top of the display. Secure it to the display using three M5

× 10mm screws.

Confirm that the frame and display are level. Adjust leveling feet, if needed.

Refer to the

Polycom EagleEye Director II Setup Sheet

to complete the EagleEye Director II

assembly.

Cable the System

Connect the HDCI cable to the codec.

Connect the 3.5mm to 2x RCA-F Y-adapter cable to the codec audio out.

Connect the camera audio cable RCA-M connectors to the Y-adapter, red to red and white to

white.

Connect the RCA cable for the right speaker to the camera audio cable red RCA-F.

Connect the RCA cable for the left speaker to the camera audio cable white RCA-F.

Apply a ferrite bead to one end of the 2M HDMI cable. Connect that end of the cable to the display

HDMI 1 input. Connect the other end to the codec primary display output.

(3) M5 x 10mm SCREW
1601-12997-001

FRAME NOT SHOWN

Summary of Contents for Poly Medialign 65






























































































































































Search results

Summary of Contents for Poly Medialign 65

Reviews:

Related manuals for Poly Medialign 65

Brands by name

Popular brands

Plantronics Poly Medialign 65, Installation Manual

Search results

Summary of Contents for Poly Medialign 65

Reviews:

Related manuals for Poly Medialign 65

Brands by name

Popular brands