background image

Self-Propelled Cultivator / Tiller 

 

 

E&OE 

©2017 Plant Craft 

25 

Air Filter 

Operating the machine without a functional air filter may cause severe engine damage and will void 
any warranty

. • A dirty or oil saturated air filter will restrict air flow, which can reduce performance 

and be mistaken as fuel system problems. Check the condition of the air filter before adjusting engine idle 
speed, where applicable

. • If the air filter is damaged (torn, broken, disintegrating), replace it. 

The air filter is used to prevent dirt and other particles from possibly entering the engine and causing internal 
damage to it. The engine breather may be connected to the air intake assembly 

– this may lead to a build-up 

of oil in the air filter over extended use and is normal. The air filter requires regular maintenance as per the 
maintenance schedule. 

Inspection and Cleaning 

Inspect the air filter for dirtiness and debris, damage etc. Clean or replace the filter element as necessary. 
The air filter housing includes an oil bath as an additional filtration safeguard, to ensure that the foam filter 
element remains well lubricated. To clean air filters: 

 

For foam filters, wash the filter in warm water and mild detergent, then rinse and allow to dry. 

 

For paper filters, use compressed air to blow particles from it. The air should be blown from the engine 
side of the filter. 

 

Clean all other air filter assembly components using water and mild detergent, then dry them. 

 

Discard any residual oil from the air filter base 
if it is contaminated and clean the air filter 
base, cover and washer in high-flashpoint 
solvent and allow to dry. Clean the engine 
where the air filter installs. 

Removal/Installation 

To remove the air filter:  

1.  Place the machine in a horizontal position on a 

flat and level surface. 

2.  Unscrew the air filter cover screw (

B

) (rotate 

left) until the washer (

C

) and air filter cover (

A

can be removed. 

3.  Pull the air filter element (

D

) from the air intake 

assembly, then remove the air filter base (

E

). 

To install the air filter: 

1.  Re-install the air filter base to the engine, 

ensuring that it is correctly oriented, then fill the 
centre section of it (where the filter element 
sits) with clean engine oil (

AA

) to the oil level 

mark (

BB

). 

2.  Insert the air filter element into the air intake 

assembly (oil bath). 

3.  Re-install the air filter cover and secure it with the air filter cover washer and screw (rotate right). 

 

 

 

AA 

BB 

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT   PLANT CRAFT

Summary of Contents for Self-Propelled Cultivator / Tiller



































Reviews: