manualshive.com logo in svg

Planex FMX-24P, User Manual, Page: 34 / 78

Share
Download
Planex FMX-24P User Manual Download Page 34

FMX-24P 

USER’S MANUAL 

 

33

PLANEX COMMUNICATIONS INC.

may not be deleted, and VLAN-1 information may not be transmitted via Tag.     
 
 
Configure Port VLAN ID 
This option is used to configure PVID (native VLAN) of each port.    The numbers 
assignable as PVID are selected from the VLAN group to which the port belongs.   
 

 

 

1) Configure Port from 

Use this option to specify the range of port numbers that you wish to 
configure.  

 
2) PVID 

Specify a PVID (number) for the port that have been selected via [Configure 
Port from].   

 
3) APPLY 

Use this option to store the current configuration to DRAM.  Select APPLY to 
modify and update the configuration of the switch that is currently running. 

 
 
Configure Port Ingress Filter 

Use this option to configure Ingress Filter of each port.  If Ingress Filter is 
enabled on a port, incoming Untag frames will be destroyed on that port upon 
their reception.   

 

Summary of Contents for FMX-24P















































































Reviews:

No comments