Planet ICS-2100T User Manual Download

Page: 43 / 76

User’s Manual of ICS-2x00T Serial Device Server Series

4.4 Network

This page allows the user to configure IPv4 or IPv6 address.

The IP configuration screen in

Figure 4-4-1

appears.

Figure 4-4-1:

IP Configuration Page Screenshot

The page includes the following fields:

IPv4

Object

Description

•

IP Configuration

Configure

static

DHCP

to get IPv4 address. The default value is

static



static

: Set a fixed IPv4 address that was manually configured for a device



DHCP

: Set IPv4 address automatically assigned from a DHCP server.

•

IP Address

The current IPv4 Address of the device. The IP Address could be manually

assigned. The default value is

192.168.0.100

•

Subnet Mask

The current IP subnet mask of the device. The default value is

255.255.255.0

•

Gateway

The default gateway for the IP interface. The default value is

192.168.0.254

•

Primary DNS

Configure the first DNS server.

•

Second DNS

Configure the second DNS server.

IPv6

Object

Description

•

IP Configuration

Configure

static

SLAAC/DHCP and disable

for IPv6 address. The default value is

disable



Static

: Set a fixed IPv6 address that was manually configured for a device



SLAAC/DHCP

: Set IPv6 addrtess automatically assigned from a DHCPv6 server.



Disable

: Disable IPv6 protocol.

•

IP Address

The current IPv6 Address of the device.

Summary of Contents for ICS-2100T













































































Search results

Summary of Contents for ICS-2100T

Reviews:

Related manuals for ICS-2100T

Brands by name

Popular brands

Planet ICS-2100T, User Manual

Search results

Summary of Contents for ICS-2100T

Reviews:

Related manuals for ICS-2100T

Brands by name

Popular brands