Planet ICS-2100T User Manual Download

Page: 26 / 76

User’s Manual of ICS-2x00T Serial Device Server Series

3. INDUSTRIAL SERIAL SERVER MANAGEMENT

This chapter covers the following topics as to how to manage the Industrial Serial Server:



Requirements



Web Management



Remote Management



PLANET Smart Discovery Utility

3.1 Requirements



Workstations

running Windows 2000/XP, 2003, Vista/7/8/10, 2008, MAC OS9 or later, or Linux, UNIX , or other

platforms compatible with

TCP/IP

protocols.



Workstation

is installed with

Ethernet NIC

(Network Interface Card)



Network cables

•

Use standard network (UTP) cables with RJ45

•

Use Multi-mode or Single-mode fiber patch cord with LC connector and 100BASE-FX SFP transceiver

(ICS-2105AT only).



The above workstation is installed with

Web Browser

and

JAVA runtime environment

plug-in

It is recommended to use Internet Explorer 7.0 or above to access Industrial Serial Server.

Summary of Contents for ICS-2100T













































































Search results

Summary of Contents for ICS-2100T

Reviews:

Related manuals for ICS-2100T

Brands by name

Popular brands

Planet ICS-2100T, User Manual

Search results

Summary of Contents for ICS-2100T

Reviews:

Related manuals for ICS-2100T

Brands by name

Popular brands