Planet ADE-3110 User Manual Download

Page: 39 / 66

server.

5.7 Bridge Filtering

Bridge Filtering allows packets to be forwarded or blocked, depending on the MAC ad-

dress. The

Bridge Filtering

configuration page allows you to set the configuration of

MAC filtering. There can be up to 4 different Bridge Filtering configurations.

Source MAC:

This is the Source MAC to block or from which to forward. See the next

page for instructions on how to configure this. The Source MAC must consist of 12

hexadecimal characters.

Destination MAC:

This is the Destination MAC to block or to forward to. See the next

page for instructions on how to configure this. The Destination MAC must consist of 12

hexadecimal characters.

Type:

Enter the hexadecimal number for the Ethernet type field in Ethernet_II packets.

For example, 0800 is for IP protocol. The Type must consist of 4 hexadecimal characters.

Block:

When block is selected, everything from the

Source MAC

with destination

Des-

tination MAC

will be blocked.

Forward:

When forward is selected, everything from the

Source MAC

will be forwarded

Summary of Contents for ADE-3110



































































Search results

Summary of Contents for ADE-3110

Reviews:

Related manuals for ADE-3110

Brands by name

Popular brands

Planet ADE-3110, User Manual

Search results

Summary of Contents for ADE-3110

Reviews:

Related manuals for ADE-3110

Brands by name

Popular brands