Planet ADE-3110 User Manual Download

Page: 15 / 66

Connect and Disconnect:

It allows you to manually connect/disconnect the PPP con-

nection for each PPP interface. In other words, each PPP session can be connected and

disconnected individually.

Connection #:

Specifies the PPP session to be connected/disconnected.

Connect/Disconnect Execute:

Press this button to either connect or disconnect.

Connection status dialog will be displayed below the

Execute

button after it is pressed.

Sample dialog with explanation:

PPP X: Connecting...

This is displayed while the PPP session is attempting to

connect to the ISP.

PPP X: Connect ERROR

This is displayed when a connection cannot be made

due to an error.

PPP X: is currently not connected

This is displayed when a disconnect attempt

is made on a session that is not currently connected.

PPP X: does not exist!

This is displayed when a connect or disconnect attempt is

made on a session number that does not exist.

4.3 ADSL Page

The

ADSL Status

page shows the ADSL physical layer or link status. The information dis-

played on this page is either inherent to the Router or set by the ADSL Central Office (CO)

DSLAM, neither of which cannot be changed by the user. This page contains information

that is dynamic and will refresh every 2 seconds.

Summary of Contents for ADE-3110



































































Search results

Summary of Contents for ADE-3110

Reviews:

Related manuals for ADE-3110

Brands by name

Popular brands

Planet ADE-3110, User Manual

Search results

Summary of Contents for ADE-3110

Reviews:

Related manuals for ADE-3110

Brands by name

Popular brands