manualshive.com logo in svg

Planet ADE-3110, User Manual, Page: 19 / 66

Share
Download
Planet ADE-3110 User Manual Download Page 19

 

14

Enable 

PPP Half Bridge 

Disabled 

Disabled 

Disabled 

Disabled 

 

DHCP Server 

Disabled 

Enabled 

Enabled 

Enabled 

 

NAT 

Disabled 

Enabled (Dynamic 

NAPT) 

Enabled (Dy-

namic NAPT) 

Enabled (Dy-

namic NAPT) 

Disabled 

DNS Proxy 

Disabled 

Enabled 

Enabled 

Enabled 

Disabled 

 

Bridge Mode:

 Bridge Mode is used when there is one PC connected to the LAN-side 

Ethernet port. IEEE 802.1D method of transport bridging is used to bridge between the 

WAN (ADSL) side and the LAN (Ethernet) side, i.e., to store and forward. 

 

Router Mode:

 Router Mode is used when there is more than one PC connected to the 

LAN-side Ethernet port. This enables the ADSL WAN access to be shared with multiple 

nodes on the LAN. Network Address Translation (NAT) is supported so that one 

WAN-side IP address can be shared among multiple LAN-side devices. DHCP is used to 

serve each LAN-side device and IP address. 

 

Summary of Contents for ADE-3110



































































Reviews:

No comments