background image

2

LC17 and LC19 User’s Guide  

(020-0599-00B)

The information contained in this document is subject to change without notice. This document 
contains proprietary information that is protected by copyright. All rights are reserved. No part of 
this document may be reproduced, translated to another language or stored in a retrieval system,
or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without
prior written permission.

Windows® is a registered trademark of Microsoft, Inc.

Other brands or product names are trademarks of their respective holders.

European Union 2002/95/EC Directive on the Restriction of Hazardous
Substances (RoHS)

In February 2003, the European Union issued Directive 2002/95/EC on the Restriction of Hazardous
Substances, commonly known as RoHS, in certain electrical and electronic equipment. It restricts 
the use of six hazardous substances, including lead (Pb).

The Directive states that all new products within its scope, placed on the European market after 
July 1, 2006 must be compliant with its requirements. 

Planar Systems Inc. is fully in support of and compliant with EU Directive 2002/95/EC for applicable
products within its scope.

A Planar part number will be modifi ed with an “LF” suffi x designation to indicate RoHS compliance,
as shown on the part number label affi xed to the display and on the box containing the display.

Important Recycle Instruction:

LCD Lamp(s) inside this product contain mercury. This product may contain other 
electronic waste that can be hazardous if not disposed of properly. Recycle or 
dispose in accordance with local, state, or federal Laws. For more information, 
contact the Electronic Industries Alliance at  HYPERLINK “http://WWW.EIAE.ORG”
WWW.EIAE.OR For lamp specific disposal information check 
WWW.LAMPRECYCLE.ORG.

_

q p

g

Summary of Contents for LC17 Series






























Reviews: