background image

Page 7

For technical questions, please call 1-800-444-3353.

Item 60805

SAFET

y

Op

ERA

TION

M

AINTENAN

c

E

SETU

p

Setup - Before Use:

  Read the ENTIRE IMpORTANT SAFETy INFORMATION section 

at the beginning of this manual including all text under 

subheadings therein before set up or use of this product.

Functions

Inlet 

Fittings

Switch

(hidden from 

this angle)

Oil Fill 

plug

Oil Drain 

plug

Oil Sight 

Glass

Operating Instructions

  Read the ENTIRE IMpORTANT SAFETy INFORMATION section 

at the beginning of this manual including all text under 

subheadings therein before set up or use of this product.

Tool Set Up

1.  Before operating the Vacuum Pump, 

check the oil level by placing the 

Vacuum Pump on a flat, level surface.  

Observe the Oil Sight Glass.  The oil should 

be at the fill line on the Oil Sight Glass.

2.  If oil is needed, unscrew the Oil Fill Plug and 

add oil through the hole under the fitting.   

Use a low viscosity vacuum pump oil 

(i.e., HFV-46).

3.  Inspect the sealing “O” Ring each time the 

Oil Fill Plug is removed.  Look for possible 

tears, cracks, or damage.  Replace if needed.

4.  Replace the Oil Fill Plug and 

tighten securely to prevent oil from 

escaping under pressure during use.

Op

ERA

TION

Summary of Contents for 3 CFM two stage













Reviews: