manualshive.com logo in svg

Piper PA-32R-301T SARATOGA S, Maintenance Manual

The Piper PA-32R-301T SARATOGA S Maintenance Manual is an essential resource for aircraft owners and mechanics. This comprehensive manual provides detailed instructions for maintenance and repairs, ensuring safe and efficient operation. Download this free manual from manualshive.com to access the necessary information for maintaining your Saratoga S aircraft.

Share
Download
background image

STABILATOR (Cont.)

BALANCING )

BALANCING EQUIPMENT (Refer to Chapter 95)

The balancing must be done using a suitable tool capable of measuring unbalance in inch-pounds from

centerline of control surface hinge pin. A suggested tool configuration is shown in Chapter 95. Other tool

configurations may be used, provided accuracy is maintained and recalibration capability is provided. The

tool shown in Chapter 95 may be calibrated by placing it on the control surface to be balanced with balance

points over control surface hinge centerline and balance bar parallel to cord line. Position trailing edge

support to align tool with control surface cord line and secure in this position. Remove tool without

disturbing trailing edge support and balance tool by adding weight to light end as required. (Movable

weight must be at centerline.) Place tool on control surface perpendicular to hinge centerline. Read scale

when bubble level has been centered by adjustment of movable weight.

– WARNING –

All control surfaces that have been replaced, repainted, or
repaired, must be rebalanced according to the procedures in
this manual.

BALANCING STABILATOR (Refer to Figure 2)

To balance stabilator, assembly must be complete including trim tab, tab pushrod and end bearing, stabilator

tips and all attaching screws. Before balancing, tape trim tab in neutral position with a small piece of tape.

Place complete assembly on knife edge supports in a draft-free beam perpendicular to hinge centerline. Do

not place tool on trim tab. Calibrate tool as described in Balancing Equipment. Read scale when bubble

level has been centered by adjustment of movable weight and determine static balance limit. If static

balance is not within limits given, proceed as follows:

1. If the stabilator is out of limits on the leading edge heavy side, remove balance plates from the mass

balance weight until the static balance is within limits.

2. If stabilator is out of limits on trailing edge heavy side, add balance plates (4 maximum) to mass

balance weight until static balance is within limits.

PIPER AIRCRAFT

PA-32R-301/301T

MAINTENANCE MANUAL

52-10-00

Page 55-4

Reissued: July 1, 1993

3I9

Summary of Contents for PA-32R-301T SARATOGA S





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PA-32R-301T SARATOGA S

Extra 330lx Information Manual preview
330lx
Brand: Extra Pages: 250
ICARO 2000 Piuma Bip Owner'S Manual preview
Piuma Bip
Brand: ICARO 2000 Pages: 44
Navair Navy F-8E Flight Manual preview
Navy F-8E
Brand: Navair Pages: 304
SOARING MODELS Cheeper Assembly Instruction Manual preview
Cheeper
Brand: SOARING MODELS Pages: 12
Cessna 177RG0073 Owner'S Manual preview
177RG0073
Brand: Cessna Pages: 85
Cessna 172 0970 Owner'S Manual preview
172 0970
Brand: Cessna Pages: 78
Topmodel WIND OF CHANGE Instruction Manual preview
WIND OF CHANGE
Brand: Topmodel Pages: 28
North Wing Horizon ET 160 Owner'S Manual preview
Horizon ET 160
Brand: North Wing Pages: 24
Atec 212 SOLO Flight Manual preview
212 SOLO
Brand: Atec Pages: 36
HPH Glasflugel 304 eS Manual preview
Glasflugel 304 eS
Brand: HPH Pages: 53
Ozone Roadster 3 Pilot'S Manual preview
Roadster 3
Brand: Ozone Pages: 37
Rans S-7LS Courier Pilot Operating Handbook preview
S-7LS Courier
Brand: Rans Pages: 82
AutoGyro RotorSport CALIDUS Pilot'S Handbook Manual preview
RotorSport CALIDUS
Brand: AutoGyro Pages: 101
Whirlwind 400A Series Owner'S Manual preview
400A Series
Brand: Whirlwind Pages: 29
UP Trango X-light2 Owner Manual And Service Booklet preview
Trango X-light2
Brand: UP Pages: 48
SUPAIR Wild 21 User Manual preview
Wild 21
Brand: SUPAIR Pages: 24
RVE Merak E750 Assembly Instructions Manual preview
Merak E750
Brand: RVE Pages: 56
Glastar JUMP-START FUSELAGE Instructions preview
JUMP-START FUSELAGE
Brand: Glastar Pages: 4

Brands by name

Popular brands

Load more brands