background image

About water-resistant (XW-SMA3 only)

CAUTION

Observe the following precautions in regard to the device

s water-resistant.

• Do not place the unit in water.
• Do not expose the unit to a large amount of water.
• Do not splash the unit with water.
• Do not expose to rain.
• Do not pour or place in warm water or water containing soap or detergent.
• Do not use in a humid environment such as a bathroom.
• Do not use near or on the beach.

This could cause rust. If exposed to seawater, thoroughly wipe off the moisture immediately with a dry cloth.

• Ensure that the terminal cover is closed during use.

The rubber packing on the cover make the device water-resistant. Make sure this packing does not get 
soiled or damaged.

If the rubber packing does become soiled, wipe it clean with a dry, clean cloth.

• Do not open the terminal cover in humid environments in which the device could get 

exposed to water.

• If the device is exposed to a large amount of water or moisture, immediately wipe it down 

with a dry cloth.

Only open or close the terminal cover after having completely wiped off any moisture around them, with dry 
hands and in an environment where the unit would not get exposed to water again.

• Make sure to install the unit on a flat and stable surface. Do not use the unit upside down 

or in a tilted position.

Since water may reach the interior of the unit, install the unit in a proper position.

• Do not turn the unit upside down or hold it tilted when it has been exposed to water or water 

droplets.

Since the water might run into the interior parts of the unit, do not tilt the unit if it is wet.

• If the device does get exposed to water, thoroughly dry all of the crevices on the unit’s body 

into which water might have reached.

The water might have reached the interior of the device. Do not carry the unit if it is still wet.

• Do not use the remote control, AC adapter when in proximity to water.

Only the device itself is water-resistant.

This unit has been designed with water-resistance equivalent to standards IPX2(*) as defined by the 
International Electrotechnical Commission (IEC).

Malfunctions due to water damage caused by improper use are not covered by product warranty, even if they 
occur within the warranty period.

• Depending on conditions of use, the water-resistant features are not necessarily 

guaranteed even during the warranty period.

*IPX2: The unit must be protected from water drops that fall vertically onto it when the unit is at an angle of 
15 degrees or less.

Use in a wet environment (XW-SMA1 and XW-SMA4 only)

CAUTION

•XW-SMA1 and XW-SMA4 are not drip-proof. When using, prevent exposure to water. Do not use in 

the following environments.

• Humid places
• Places where the product is easily exposed to water
• Near the beach or on the beach

This could cause rust.

Summary of Contents for XW-SMA1

















































Reviews: