background image

Thank you for buying this Pioneer product.
Please read through these operating instructions so 
you will know how to operate your model properly.  
After you have finished reading the instructions, put 
them away in a safe place for future reference.
In some countries or regions, the shape of the power 
plug may sometimes differ from that shown in the 
explanatory drawings.  However, the method of con-
necting and operating the unit is the same.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance. 

The lightning flash with arrowhead symbol, 
within an equilateral triangle, is intended to 
alert the user to the presence of uninsulated 
"dangerous voltage" within the product's 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock to persons.

IMPORTANT

CAUTION:

TO PREVENT THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR 
BACK).  NO USER-SERVICEABLE PARTS 
INSIDE.  REFER SERVICING TO QUALIFIED 
SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

D3-4-2-1-1_En

Do not connect either wire to the earth terminal of a 
three pin plug.

NOTE
After replacing or changing a fuse, the fuse cover in 
the plug must be replaced with a fuse cover which 
corresponds to the colour of the insert in the base 
of the plug or the word that is embossed on the 
base of the plug, and the appliance must not be 
used without a fuse cover. If lost replacement fuse 
covers can be  obtained from your dealer. 
Only  5 A  fuses approved by B.S.I or A.S.T.A to 
B.S.1362 should be used.

 

 

 

D3-4-2-1-2-2_En

The wires in this mains lead are coloured in 
accordance with the following code:
 

Blue : 

Neutral

 

Brown : Live

If the plug provided is unsuitable for your socket 
outlets, the plug must be cut off and a suitable plug 
fitted. 

IMPORTANT

FOR USE IN THE UNITED 
KINGDOM

The cut-off plug should be disposed of and must 
not be inserted into any 13 amp socket as this can 
result in electric shock. The plug  or  adaptor or the 
distribution panel should be provided with 5 A fuse.  
As the colours of the wires in the mains lead of this 
appliance may not correspond with coloured 
markings identifying the terminals in your plug, 
proceed as follows ;
The wire which is coloured blue must be connected 
to the terminal which is marked with the letter N or 
coloured black.
The wire which is coloured brown must be 
connected to the terminal which is marked with the 
letter L or coloured red.

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified 
service personnel.

WARNING: 

The apparatus is not waterproofs, to 

prevent fire or shocks hazard, do not expose this 
apparatus to rain or moisture and do not put any 
water source near this apparatus, such as vase, 
flower pot, cosmetics container and medicine 
bottle etc.     

D3-4-2-1-3_En

The STANDBY/ON switch is secondary connected 
and therefore, does not separate the unit from mains 
power in STANDBY position. Therefore install the 
unit suitable places easy to disconnect the MAINS 
plug in case of the accident. The MAINS plug of unit 
should be unplugged from the wall socket when left 
unused for a long period of time.  

D3-4-2-2-2a_En

This product is for general household purposes. 
Any failure due to use for other than household 
purposes (such as long-term use for business 
purposes in a restaurant or use in a car or ship) 
and which requires repair will be charged for even 
during the warranty period.

K041_En

WARNING: 

BEFORE PLUGGING IN THE UNIT FOR THE FIRST 
TIME, READ THE FOLLOWING SECTION CAREFULLY. 
The voltage of the available power supply differs 
according to country or region. Be sure that the 
power supply voltage of the area where this unit 
will be used meets the required voltage (e.g., 230V 
or 120V) written on the rear panel. 

D3-4-2-1-4_En

WARNING: 

No naked flame sources, such as 

lighted candle, should be placed on the apparatus. 
If naked flame sources accidentally fall down, fire 
spread over the apparatus then may cause fire.
 

   

D3-4-2-1-7a_En

CAUTION

The POWER switch does not completely separates 
the unit from the MAINS in off position. Therefore 
install the unit suitable places easy to disconnect 
the MAINS plug in case of the accident. The MAINS 
plug of unit should be unplugged from the wall 
socket when left unused for a long period of time. 
 

   

D3-4-2-2-2b_En

Operating Environment

Operating environment temperature and humidity:
+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH 
(cooling vents not blocked)
Do not install in the following locations
•  Location exposed to direct sunlight or strong artificial 

light

•  Location exposed to high humidity, or poorly 

ventilated location

 

D3-4-2-1-7c_En

VENTILATION: 

When installing this unit, make 

sure to leave space around the unit for ventilation 
to improve heat radiation (at least 20 cm at top, 50 
cm at rear, and 10 cm at each side).

WARNING: 

Slot and openings in the cabinet are 

provided for ventilation and to ensure reliable 
operation of the product and to protect it from 
overheating, to prevent fire hazard, the openings 
should never be blocked and covered with items, 
such as newspapers, table-cloths, curtains, etc. Also 
do not put the apparatus on the thick carpet, bed, 
sofa, or fabric having a thick pile. 

D3-4-2-1-7b_En

This product complies with the Low Voltage Directive 
(73/23/EEC, amended by 93/68/EEC), EMC Directives 
(89/336/EEC, amended by 92/31/EEC and 
93/68/EEC).  

 

 

D3-4-2-1-9a_En

vsx-c402_MY.book 2 ページ 2004年2月6日 金曜日 午後7時19分

Summary of Contents for VSX-C402















































Reviews: