Additional information
12
79
En
Video
When playing a DTS format LD
there is audible noise on the
soundtrack.
• Make sure that the input signal type is set to
DIGITAL
(see
Choosing the input signal
on page 30).
Can't record audio.
• You can only make a digital recording from a digital source, and an analog recording from an analog
source.
• For digital sources, make sure that what you’re recording isn’t copy protected.
• Check that the
OUT
jacks are properly connected to the recorders input jacks (see
Connecting analog
audio sources
on page 16).
Recorded audio is different from
the current source, or inaudible.
• The
RECOUT
source is set to an input source other than the source you’re listening to. Select
RECOUT
SOURCE
to record the current input source (see
Playing a different source when recording
on page 67).
Subwoofer output is very low.
• To route more signal to the subwoofer, set it to
PLUS
or set the front speakers to
SMALL
(see
Speaker
Setting
on page 43).
Everything seems to be set up
correctly, but the playback sound
is odd.
• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are
matched with the corresponding terminals on the speakers (see
Connecting the speakers
on page 17).
The
PHASE CONTROL
feature
doesn’t seem to have an audible
effect.
•If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to
the highest frequency setting. If there is a
PHASE
setting on your subwoofer, set it to 0º (or depending on
the subwoofer, the setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see
Speaker Distance
on page 45).
Noise or hum can be heard even
when there is no sound being
input.
• Check that personal computers or other digital components connected to the same power source are not
causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• See
Automatically setting up for surround sound (MCACC)
on page 7 to set up your system again using
MCACC (this will automatically compensate for a delay in the subwoofer output).
The maximum volume available
(shown in the front panel display)
is lower than the
+12dB
maximum.
• This is not a malfunction. If the levels in
Channel Level
on page 44 have been adjusted, the maximum
volume will change accordingly.
Symptom
Remedy
Symptom
Remedy
No image is output when an
input is selected.
• Check the video connections of the source component (see page 13).
• For high-definition video (using component video connections), or when digital video conversion is
switched off (in
Setting the AV options
on page 66), you must connect your TV to this receiver using the same
type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component or S-video cables
(see
The Input Setup menu
on page 63).
• A separate video source has been selected using
VIDEO SELECT
(see
Watching video and audio sources
independently
on page 68).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If adjusting
this receiver’s
Resolution
setting (in
Setting the AV options
on page 66) and/or the resolution settings on
your component or display doesn’t work, try switching Digital Video Conversion (in
Setting the AV options
on page 66)
OFF
.
Can’t record video.
• Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video cable is
used for connecting both the recorder and the video source (the one you want to record) to this receiver.
VSX_84TXSi.book.fm 79 ページ ２００６年３月１３日 月曜日 午前１１時５４分
