71
KRP-M01
5
6
7
8
5
6
7
8
A
B
C
D
E
F
After analysis is finished
Products whose proper operation has been proved
when HDMI connection is performed with this MR
After analysis in Standalone Operation mode is finished, before returning the MR to the customer, be sure to return
the unit to System Operation mode, as shown in the procedures below.
If it remains in Standalone Operation mode, when it is connected with the customer’s monitor, the monitor will detect
a connection error and not operate properly, and no image will be displayed.
To set the MR to System Operation mode, proceed as follows:
[With an RS-232C command]
1. Turn the MR on.
2. Send the MRMS00 command via RS-232C ports.
3. Turn the MR off.
W
hen the MR is turned on next time or after, it will be in System Operation mode.
4. Connect the MR directly with the monitor and check that they operate properly.
[With the keys on the MR]
1. Set the MR to Standby mode.
2. Press and hold the I
N
PUT key of the MR pressed for at least 5 seconds.
(This step is for giving a startup trigger in a case where the MR was in Passive Standby mode.)
3.
W
ithin 5 seconds after the I
N
PUT key is released, press and hold the CHA
NN
EL + key of the MR for at least 10 seconds.
4. After the modes are changed, the red LED flashes twice then is lit (the unit enters
N
ormal Standby mode).
5. Turn the unit off.
W
hen the MR is turned on next time or after, it will be in Standalone Operation mode.
Attention point for audio volume
Audio output level is connected with MR volume level. If
V
R level of a MR is normal ( around 10 - 15) and displayed
HDMI T
V
or audio AMP is not so high level, sound level is very low. Please turn up the volume to appropriate level either
or both units.
In case of turning up volume of MR to very high level during testing, turn down it to normal level and then turn off the unit.
Otherwise when connecting the MR with panel, very loud sound is output from speakers and it might be a danger.
Attention point when usin
g
another Pioneer Plasma TV
Please pay attention to interference of IR signal when using Pioneer plasma T
V
as HDMI monitor.
If remote signal is also received to Pioneer plasma T
V
when operating MR with this tool and remote, you might confuse
of which unit is controlled by the remote.
The following methods are some of suggestions to control only MR with the conversion tool.
Using the remote control unit and the conversion tool ( AC adaptor connector ) as nearly as possible hiding remote sensor
of the plasma T
V
temporally.
Settin
g
Method to connect with DVI monitor with HDCP support (DVI mode)
1. Open bonnet with power off condition.
2. Refer to Fig. 3, move the DIP S
W
N
o. [4] to O
N
side.
After this setting, D
V
I mode signal is output from HDMI output connector of HDMI.
Note:
1. Some of D
V
I monitors might not display output signal from this conversion tool.
2. Output signal does not contain digital audio signal.
Model Number
Manufacturer
Built-in Audio AMP
PDP-5000EX
G8
FP241
W
J
3008
W
FP
HD2441
W
Pioneer
Pioneer
BenQ
DELL
EIZO
N
A
N
AO
(SP is required)
(SP is required except 42 inch)
(External audio amp and SP is required)
(External audio amp and SP is required)
(External audio amp and SP is required)
Summary of Contents for krp-m01
Page 8: ...8 KRP M01 1 2 3 4 A B C D E F 1 2 3 4 2 3 PANEL FACILITIES ...
Page 9: ...9 KRP M01 5 6 7 8 5 6 7 8 A B C D E F Remote Control Unit ...
Page 14: ...14 KRP M01 1 2 3 4 A B C D E F 1 2 3 4 4 BLOCK DIAGRAM 4 1 OVERALL WIRING DIAGRAM ...
