GEX-P10XMT/XN/UC
47
5
6
7
8
5
6
7
8
C
D
F
A
B
E
E6 ERV_UNAVAIL
Designated program is not found.
E7 TYPE_UNAVAIL
Program with designated service type is not found.
E8 PROG_UNAVAIL
Program with designated category is not found.
E9 UNKNOWN_PC
PC format is not standard.
EA ACT_REQ
Activation required
EB AUTH_REQ
Authorization required
EC OFFAIR
Service being off-air
ED DIFF_ENS
Designated Primary and Secondary PCID are not found on the same ensemble.
EE PC_UNDETECT
Unable to receive PC of selected program
EF SID_UNDETECT
Unable to identify SID of selected program
F0 SCT_UNDETECT
Unable to identify the service component type of selected program
F1 AUTH_MISS
Updating encryption key
F3 RAT_BLOCK
Being out of contract
F4 RAT_LOW
A program out of the contract was selected.
F5 TOD_ROLLBACK
The time information controlled in DSP core does not match the time
information during on-air.
F6 IDLE_WT
Preparing for control completion
F7 DIFF_PCID
PCID discrepancy
FF REQ_RETRY
SSDEC error occurred (restart required)
Display example: If the system is receiving, the display will momentarily show [M2_00_20].
4.12 ANTENNA PASS
No display.
If an antenna is not connected, and if this setting is made while the system is displaying the "ANTENNA" message,
connection checks will not be conducted until the system has been reset (the system will assume normal operation
without an antenna check).
4.13 QOS Message
Display format : [ 1 A A B B C C D ]
A : The Viterbi error rate (two effective digits of decimal value) of ground wave. (*1)
B : The Viterbi error rate (two effective digits of decimal value) of satellite wave 1. (*1)
C : The Viterbi error rate (two effective digits of decimal value) of satellite wave 2. (*1)
D : The quality of service (QOS) value (a single effective digit decimal value). (*2)
*1 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will
show "-". For 100, the display will show "XX". If a signal is not received, the display will show "NS."
*2 : The single digit display may show from 0 to 9. If the display information is being acquired, the display will
show "-". For 10 and over, the display will show "X".
4.14 TERR Message
Display format : [ 2 A B B C C D D ]
A : The locking status of the ground wave. (*1)
B : The ground wave Viterbi signal error rate (two effective digits of decimal value). (*2)
C : The ground wave Read-Solomon symbol error rate (two-effective digits of decimal value). (*3)
D : The ground wave Read-Solomon non-correction code word (two effective digits of decimal value). (*4)
*1 : The "-" will be displayed while the system is acquiring the information, "N" if the signal is not locked on, "D"
if only the demodulator is locked, and "T" if both the TDM and demodulator are locked on.
*2 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will
show "-". For 100, the display will show "XX". If a signal is not received, the display will show "NS."
*3 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will
show "-". For 100, the display will show "XX".
*4 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will
show "-". For 100, the display will show "XX".
Summary of Contents for GEX-P10XMT - Satellite Radio Tuner
