Pioneer Elite PRB-19RW Operating Instructions Manual Download Page 38

Page: 38 / 40

Additional Information

It’s often easy to mistake incorrect operation for trouble and malfunction of the unit. If you think there is something wrong
with the component, check the points below first. If the problem persists, contact you nearest Pioneer-authorized service
center and have them check over the unit.

Symptom

Power cannot be turned
on.

No sound is heard
during playback.

Cannot record.

Recorded sound is
distorted.

Remote control opera-
tion is impossible.

Some tracks are skipped
without being played.

Skip playback does not
occur.

A recorded

–

disc

cannot be played on
other

players.

The point-of-sale
demonstration is
displayed.

Cause

The power cord is unplugged from the wall
outlet.

The power was turned off from the compo-
nent (stereo amplifier, audio timer, etc.) to
which it is connected.

The recorder is not connected up properly.

The

–

disc in use has already

been finalized.

The input selection is incorrect.

The analog

REC

LEVEL

control is set too low.

The analog recording level is set too high.

Signal connections are incorrect.

There is interference from a TV set.

The disc is damaged or warped.

The disc is extremely dirty.

The remote control batteries are exhausted.

There is an obstacle between the remote
control unit and main unit.

The remote control unit is being operated
outside the remote controllable range.

The

SKIP

PLAY

button is set to on.

The

SKIP

PLAY

button is set to off.

The disc has not been finalized after
recording. When such a disc is loaded in the
unit, the

–

indicator lights.

The pickup lens of the other

player is

dirty, impairing its ability to play

–

discs.

See page 36 for instructions on how to cancel
the store demo mode.

Remedy

Plug the power cord into a power outlet.

Turn on the component supplying the
power to the recorder.

Check all connections, especially to the
amplifier — pp.10–11

Check all connections — pp.10–11

Use a non-finalized disc or erase the

–

disc — pp.34–35

Select the input connected to the source
component you’re recording from.

Increase the recording level — p.24

Reduce the analog recording level —p.24

Check all connections — pp.10–11

Turn the

power off or install this unit

further away from the

Use another disc.

Clean the disc.

Replace both of the remote control
batteries with new ones.

Remove the obstacle.

Operate in the remote controllable
range —p.14

Set the

SKIP

PLAY

button to off — p.27

Set the

SKIP

PLAY

button to on —p.27

Finalize the disc — p.33

Try the disc on a different

player. If it

plays

then get the pickup lens on the

original player cleaned.

Summary of Contents for Elite PRB-19RW









































Search results

Summary of Contents for Elite PRB-19RW

Reviews:

Related manuals for Elite PRB-19RW

Brands by name

Popular brands

Pioneer Elite PRB-19RW, Operating Instructions Manual

Search results

Summary of Contents for Elite PRB-19RW

Reviews:

Related manuals for Elite PRB-19RW

Brands by name

Popular brands