Pioneer Elite PRB-19RW Operating Instructions Manual Download Page 35

Page: 35 / 40

Additional Features

Additional Recording Features

◊ÛB

,/Bˆ

Digital Recording System

Erasing all tracks on a disc

Load a CD–RW.

Press ERASE twice for a non-finalized CD–RW,
or once for a finalized disc.

The recorder prompts you to confirm with the message

ALL

TRACK

ERASE

, and the recorder function indicator blinks

orange to indicate erase standby mode.

❖

Press

(stop) to cancel all track erase here.

❖

If you don't proceed to step 3 within eight seconds, all track erase
is cancelled.

Press

(pause) to start erasing.

The process takes about three minutes for a finalized

–

. During

this time, the function indicator lights orange and the display shows

ERS

to indicate that the recorder is erasing the disc and the remaining time to
completion.
If the disc is not yet finalized, the display shows the message

ALL

TRACK

ERASE

while the recorder erases the disc. This takes just a few seconds.

Re-initializing a disc

Load a CD–RW.

Press and hold ERASE for about four seconds.

The recorder prompts you to confirm with the message

ALL

DISC

ERASE

and the recorder function indicator blinks orange to indicate erase
standby mode.

❖

Press

(stop) to cancel all disc erase here.

Press

(pause) to start erasing.

The process takes about five minutes plus the entire length of the disc.
During this time, the function indicator lights orange and the display
shows

(disc erase), followed by the remaining time to completion.

Hi-bit Legato Link Conversion

Function indicator lights
in orange when erasing

Summary of Contents for Elite PRB-19RW









































Search results

Summary of Contents for Elite PRB-19RW

Reviews:

Related manuals for Elite PRB-19RW

Brands by name

Popular brands

Pioneer Elite PRB-19RW, Operating Instructions Manual

Search results

Summary of Contents for Elite PRB-19RW

Reviews:

Related manuals for Elite PRB-19RW

Brands by name

Popular brands