5
En
English
Connections
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Refer to the operating instructions for the component to be connected.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.
Rear panel
AC IN
MASTER 1
LOW CUT
25Hz
OFF ON
USB
ZONE
BOOTH
R
R
L
L
R
L
CH-1
CH-2
CH-3
MASTER 2
SEND
RETURN
R
(MONO)
(TRS)
(TRS)
(TRS)
R
L
L
SUBWOOFER
REC OUT
R
L
CH-4
1GND
SIGNAL
GND
CD
CD
PHONO/LINE
LINE
2 HOT
3 COLD
LINE PHONO
R
L
R
L
CD
LINE
R
L
SIGNAL
GND
CD
PHONO/LINE
LINE PHONO
R
L
R
L
1
2 3 4
5 6
5 6
523 4
5
7
8
9
a
b
c
d
e
f
g
1
MASTER 1 terminals (page 6)
Connect to a power amplifier, etc.
2
PHONO/LINE selector switch (page 6)
Switches the function of the [
PHONO/LINE
] terminals.
CAUTION
When switching the [
PHONO/LINE
] selector switch, set
[
MASTER LEVEL
] to [-∞]. Note that noise may be generated and sound
output at a high volume.
3
SIGNAL GND terminal (page 6)
Connects an analog player’s ground wire here. This helps reduce
noise when the analog player is connected.
4
PHONO/LINE terminals (page 6)
Connect a phono level output device (analog player (for MM car-
tridges), etc.) or a line level output device (DJ player, etc.) here.
Switch the terminals’ function according to the connected device
using the [
PHONO/LINE
] selector switch on this unit’s rear panel.
5
CD terminals (page 6)
Connect to a DJ player or a line level output component.
6
LINE terminals (page 6)
Connect to a cassette deck or a line level output component.
7
RETURN terminals (page 6)
Connect to the output terminal of an external effector. When the [
L
(MONO)
] channel only is connected, the [
L (MONO)
] channel input
is simultaneously input to the [
R
] channel.
8
USB terminal (page 7)
Connect to a computer.
A USB hub cannot be used.
9
SEND terminals (page 6)
Connect to the input terminal of an external effector. When the [
L
(MONO)
] channel only is connected, a monaural audio signal is
output.
a
ZONE terminals (page 6)
Output terminals for the [
ZONE
] channel, compatible with balanced
or unbalanced output for a TRS connector.
b
BOOTH terminals (page 6)
Output terminals for a booth monitor, compatible with balanced or
unbalanced output for a TRS connector.
c
SUBWOOFER terminals (page 6)
Output terminals for a subwoofer, compatible with balanced or
unbalanced output for a TRS connector.
d
REC OUT terminals (page 6)
These are output terminals for recording.
e
MASTER 2 terminals (page 6)
Connect to a power amplifier, etc.
f
LOW CUT selector switch (page 10)
Turns the low cut function on and off.
g
AC IN
Connects to a power outlet using the included power cord. Wait until
all connections between the equipment are completed before con-
necting the power cord.
Be sure to use the included power cord.
WARNING
The short-circuit pin plugs out of the reach of children and infants. If
accidentally swallowed, contact a doctor immediately.
Summary of Contents for DJM-4000
Page 3: ...3 Zhcn ...
