Pioneer DJM 3000 - Professional DJ Mixer, Service Manual

Page: 105 / 107

DJM-3000
105
5 6 7 8
5 6
7
8
C
D
F
A
B
E
Rotate clockwise to increase response (to +12 dB), and rotate
counterclockwise to decrease response (to –26 dB).
=
H.P CUE (Headphones cue switch)
When this switch is pressed it lights orange and the
corresponding channel is output to headphones. When the
switch is pressed again the light goes out and the channel’s
output to the headphones is cut.
When the beat effector function is set to AUTO BPM, this
switch functions to select the BPM display channel.
~
Peak level meter
Peak levels are displayed as they occur and maintained for 2
seconds.
Displays output level before channel fader adjustment.
Displayable range is from –22 dB to +14 dB.
!
Channel fader lever
Use to adjust the sound level at each channel.
π
MASTER (Master Controls)
@
MONO/STEREO selector switch
Use to select whether the master output and booth monitor
output are monaural or stereo.
#
MASTER LEVEL meter
Displays output level following adjustment of the MASTER
fader lever, and holds the display for 2 seconds. Displayable
range is from –22 dB to +14 dB.
$
H.P CUE (Headphones cue switch)
When this switch is pressed it lights orange and the master
output is heard in the headphones. When the switch is pressed
again the light goes out and the master output to the
headphones is cut.
%
MASTER fader lever
Use to control the master output level.
The rear panel MASTER LEVEL ATT. control can also be
used to reduce the output level.
^
MASTER BALANCE control
Use to adjust the balance of right-left channels for master
output and booth monitor output.
[
BOOTH MONITOR Control
Use to adjust the output at the BOOTH MONITOR connectors
on the rear panel. Not affected by the MASTER fader lever (
%
).
“
POWER Switch
]
HEADPHONES Controls
&
MONO SPLIT/STEREO selector switch
Use to select whether to split monitor sound on the left and
right of the headphones or to keep sound in stereo form.
When set to MONO SPLIT, the headphones output is set to
2-channel monaural; the Left channel becomes the source
selected with the H.P CUE switch, while the Right channel
becomes the master output sound (only when MASTER H.P
CUE switch is set to ON).
*
MIXING control
Use to adjust the headphones monitor sound.
When rotated fully clockwise, the master output sound only is
heard (only when MASTER H.P CUE switch is set to ON).
When rotated fully counterclockwise, only the channel
selected with the H.P CUE switch (other than MASTER) is
heard.
At the center click position, the master output and source
selected with the H.P CUE switch are at equal levels.
(
LEVEL control
Use to control the headphones monitor level. When one of
CH-1 to CH-4 is selected, this control is not affected by the
MASTER fader lever (
%
) and the MASTER BALANCE
control (
^
).
)
PHONES (headphones jack)
‘
Cross Fader Controls
_
CROSS FADER ASSIGN A switch
When using the cross fader with two sources (A, B), this
switch selects the source assigned to A.
THRU: When cross fader is not used, sets to THRU.
1-4:
Use to select the channel (CH-1 to CH-4) assigned to
A.
Channels other than those assigned to A and B can be
output without passing through the cross fader.
+
CROSS FADER CURVE selector switch
Use to select one of three rising curve patterns for the cross
fader function.
¡
Fader display A
During the effect mix mode, displays the output of sounds
from the channel selected with the CROSS FADER ASSIGN
A switch.
™
Cross fader lever
Use to adjust the mix of sounds from the sources assigned to
A and B by the ASSIGN switches (
_
) and (
¢
).
£
Fader display B
During the effect mix mode, displays the output of sounds
from the channel selected with the CROSS FADER ASSIGN
B switch.
¢
CROSS FADER ASSIGN B switch
When using the cross fader with two sources (A, B), this
switch selects the source assigned to B.
THRU: When cross fader is not used, sets to THRU.
1-4:
Use to select the channel (CH-1 to CH-4) assigned to
B.
Channels other than those assigned to A and B can be
output without passing through the cross fader.
\
FADER START Switches
CH-1, CH-2, CH-3, CH-4
When a CD player (CMX-3000, CMX-5000, CDJ-1000, CDJ-
100S, CDJ-700S or CDJ-500II) is connected to one of the
above channels of this unit via a control cord, the CD player’s
CUE START/STOP operation will start when the channel
fader is moved from “0” upwards, and will stop (back cue)
when the channel fader is returned to “0”. The indicator of the
selected channel will light orange during this operation. Also,
if a channel is assigned to the cross fader, the cross fader is
given priority; when the Cross fader lever begins moving from
the A side toward B side, the CD player assigned to the B side
will start, and when the lever reaches the B side, the A side
source will stop (back cue).