Pioneer DEH-X7600HD, Owner'S Manual

Page: 25 / 112

Black plate (25,1)
9
Gray/black
a
Green
b
Green/black
c
Violet
d Violet/black
e
Black (chassis ground)
Connect to a clean, paint-free metal location.
f
Yellow
Connect to the constant 12 V supply termi-
nal.
g
Red
Connect to terminal controlled by ignition
switch (12 V DC).
h
Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control ter-
minal (max. 300 mA 12 V DC).
i
Orange/white
Connect to lighting switch terminal.
j Subwoofer (4
W
)
k
When using a subwoofer of 70 W (2
W
), be
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
l
Not used.
m
Subwoofer (4
W
) × 2
Notes
!
When using a two-speaker system, do not
connect anything to speaker leads that are
not connected to a speaker.
!
Change the set up menu of this unit. Refer to
S/W control (rear output and subwoofer set-
ting) on page 20.
The subwoofer output of this unit is monau-
ral.
Power amp (sold separately)
Perform these connections when using the op-
tional amplifier.












1
1
3
2
4
5 5
3
2
6
7 7
1
3
2
8
9 9
1
System remote control
Connect to Blue/white cable.
2
Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4
To Rear output
5
Rear speaker
6
To Front output
7
Front speaker
8 To subwoofer output
9
Subwoofer
Installation
Important
!
Check all connections and systems before
final installation.
!
Do not use unauthorized parts as this may
cause malfunctions.
!
Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
!
Do not install this unit where:
—
it may interfere with operation of the vehicle.
—
it may cause injury to a passenger as a result
of a sudden stop.
!
The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
!
Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
!
When installing, to ensure proper heat dis-
persal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not block-
ing the vents.
5cm cm
Leave ample
space
5 cm
5 cm
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
Use commercially available parts when instal-
ling.
DIN Front-mount
1 Insert the mounting sleeve into the dash-
board.
For installation in shallow spaces, use the sup-
plied mounting sleeve. If there is enough space,
use the mounting sleeve that came with the ve-
hicle.
2 Secure the mounting sleeve by using a
screwdriver to bend the metal tabs (90°) into
place.
1
2
1 Dashboard
2
Mounting sleeve
#
Make sure that the unit is installed securely in
place. An unstable installation may cause skipping
or other malfunctions.
DIN Rear-mount
1 Determine the appropriate position
where the holes on the bracket and the side
of the unit match.
2 Tighten two screws on each side.
1
2
3
1
Screw
2
Mounting bracket
3 Dashboard or console
!
Use either truss (5 mm × 8 mm) or flush sur-
face (5 mm × 9 mm) screws, depending on
the bracket screw holes.
English
Installation
25
Section
Installation
En
04
<QRD3228-A>25