background image

Connecting the units

English

Connecting the units

English

 Note

•  When this unit is installed in a vehicle without 

ACC (accessory) position on the ignition switch, 

red cable must be wired to the terminal that can 

detect the operation of the ignition key. Otherwise, 

battery drain may result.

ACC

ON

S

T

A

R

T

O

FF

      

ON

S

T

A

R

T

O

FF

ACC position

      

No ACC position

•  Use this unit in other than the following 

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative 

grounding.

— Speakers with 50 W (output value) and 4 ohm 

to 8 ohm (impedance value).

•  To prevent short-circuit, overheating or 

malfunction, be sure to follow the directions 

below.

— Disconnect the negative terminal of the 

battery before installation.

— Secure the wiring with cable clamps or 

adhesive tape. To protect the wiring, wrap 

adhesive tape around them where they lie 

against metal parts.

— Place all cables away from moving parts, such 

as gear shift and seat rails.

— Place all cables away from hot places, such as 

near the heater outlet.

— Do not pass the yellow cable through a hole 

into the engine compartment to connect to a 

battery.

— Cover any disconnected cable connectors with 

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of 

this unit in order to share the power to other 

equipment. Current capacity of the cable is 

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly 

to ground.

— Never band together multiple speaker’s 

negative cables.

•  Control signal is output through blue/white cable 

when this unit is powered on. Connect it to an 

external power amp’s system remote control or 

the vehicle’s auto-antenna relay control terminal 

(max. 300 mA, 12 V DC). If the vehicle is equipped 

with a glass antenna, connect it to the antenna 

booster power supply terminal.

•  Never connect blue/white cable to external power 

amp’s power terminal. Also, never connect 

it to the power terminal of the auto antenna. 

Otherwise, battery drain or malfunction may 

result.

•  IP-BUS connectors are color-coded. Be sure to 

connect connectors of the same color.

•  Black cable is ground. This cable and other 

product’s ground cable (especially, high-current 

products such as power amp) must be wired 

separately. Otherwise, fire or malfunction may 

result if they are accidentally detached.

30.Power amp 
(sold separately)

29.Connect with RCA cables  
 (sold 

separately)

31.System remote control

30.Power amp 
(sold separately)

30.Power amp 
(sold separately)

28.To front output

27.To rear output

33. Rear speaker

34. Subwoofer

32. Front speaker

33. Rear speaker

34. Subwoofer

32. Front speaker

26.To subwoofer 

output

6. Wired remote input 

Hard-wired remote 
control adaptor can 
be connected (sold 
separately).

7.Fuse (10 A)

8.IP-BUS input (Blue)

9.IP-BUS cable

35. Perform these connections when 

using the optional amplifier.

3. Front output

5. Antenna jack

1. This product

1*

3*

2*

4*

5*

11. 

Note

 

Depending on the kind of vehicle, 
the function of 3* and 5* may be 
different. In this case, be sure to 
connect 2* to 5* and 4* to 3*.

12. Connect leads of the 

same color to each other.

13. Cap (1*) 
 

Do not remove cap 
if this terminal is 
not in use.

14. Yellow (3*) 
 Back-up 

(or 

accessory)

16. Red (5*)
 Accessory 

(or back-up)

15. Yellow (2*) 
 

Connect to the constant 
12 V supply terminal.

17. Red (4*) 
 

Connect to terminal controlled by 
ignition switch (12 V DC).

18. Orange/white 
 

Connect to lighting switch terminal.

25. Speaker leads 
 White: 

Front 

left 

 

 White/black: 

Front 

left 

 Gray: 

Front 

right 

 

 Gray/black: 

Front 

right 

 

 Green: 

Rear 

left 

 or subwoofer 

 Green/black: 

Rear 

left 

 or subwoofer 

 

 Violet: 

Rear 

right 

 or subwoofer 

 Violet/black: 

Rear 

right 

 or subwoofer 

22. Blue/white
 

Connect to system control terminal of the 
power amp (max. 300 mA 12 V DC).

23. Blue/white (7*) 
 

Connect to auto-antenna relay control 
terminal (max. 300 mA 12 V DC).

19. Black (chassis ground) 
 

Connect to a clean, paint-free metal location.

The pin position of the ISO 
connector will differ depends on the 
type of vehicle. Connect 6* and 7* 
when Pin 5 is an antenna control 
type. In another type of vehicle, 
never connect 6* and 7*.

24. Blue/white (6*) 

2. Rear output

10.Multi-CD player 

(sold separately)

36. 

Notes

• Change the initial setting of this unit (refer to the 

operation manual). The subwoofer output of this unit is 
monaural.

• When using a subwoofer of 70 W (2 

), be sure to 

connect with Violet and Violet/black leads of this unit. 
Do not connect anything with Green and Green/black 
leads. 

4. Subwoofer output

20. ISO connector

 Note

 

In some vehicles, the ISO connector may be 
divided into two. In this case, be sure to 
connect to both connectors.

21. Yellow/black
 

If you use an equipment with Mute 
function, wire this lead to the Audio Mute 
lead on that equipment. If not, keep the 
Audio Mute lead free of any connections.

Connection Diagram

1. This product
2. Rear output
3. Front output
4. Subwoofer output
5. Antenna jack
6.  Wired remote input

Hard-wired remote control adaptor can be 

connected (sold separately).

7. Fuse (10 A)
8. IP-BUS input (Blue)
9. IP-BUS cable
10. Multi-CD player (sold separately)
11. Note
  Depending on the kind of vehicle, the function 

of 3* and 5* may be different. In this case, be 
sure to connect 2* to 5* and 4* to 3*.

12. Connect leads of the same color to  

each other.

13. Cap (1*) 
  Do not remove cap if this terminal is not in use.
14. Yellow (3*) 
  Back-up (or accessory)
15. Yellow (2*) 
  Connect to the constant 12 V supply terminal.
16. Red (5*)
  Accessory (or back-up)
17. Red (4*) 
  Connect to terminal controlled by ignition 

switch (12 V DC).

18. Orange/white 
  Connect to lighting switch terminal.
19. Black (chassis ground) 
  Connect to a clean, paint-free metal location.
20. ISO connector
 Note
  In some vehicles, the ISO connector may 

be divided into two. In this case, be sure to 
connect to both connectors.

21. Yellow/black
  If you use an equipment with Mute function, 

wire this lead to the Audio Mute lead on that 
equipment. If not, keep the Audio Mute lead 
free of any connections.

22. Blue/white
  Connect to system control terminal of the 

power amp (max. 300 mA 12 V DC).

23. Blue/white (7*) 
  Connect to auto-antenna relay control terminal 

(max. 300 mA 12 V DC).

24. Blue/white (6*)
  The pin position of the ISO connector will differ 

depends on the type of vehicle. Connect 6* 
and 7* when Pin 5 is an antenna control type. 
In another type of vehicle, never connect 6* 
and 7*.

25. Speaker leads

White: Front left 

White/black: Front left 

Gray: Front right 

Gray/black: Front right 

Green: Rear left 

 or subwoofer 

Green/black: Rear left 

 or subwoofer 

Violet: Rear right 

 or subwoofer 

  Violet/black: Rear right 

 or subwoofer 

26. To subwoofer output
27. To rear output
28. To front output
29. Connect with RCA cables (sold separately)
30. Power amp (sold separately)
31. System remote control
32. Front speaker
33. Rear speaker
34. Subwoofer
35. Perform these connections when using the 

optional amplifier.

36. Notes

•  Change the initial setting of this unit (refer 

to the operation manual). The subwoofer 

output of this unit is monaural.

•  When using a subwoofer of 70 W (2 

), be 

sure to connect with Violet and Violet/black 

leads of this unit. Do not connect anything 

with Green and Green/black leads.

Summary of Contents for DEH-P5100UB - Radio / CD









Reviews: