background image

NEVER LEAVE HEATER UNATTENDED WHILE BURNING 

OR WHILE CONNECTED TO A POWER SOURCE

© 2017, Pinnacle Climate Technologies, Inc. 

Kerosene Forced Air Heater User’s Manual 

4

What’s In The Box Models: 135T-KFA / 175T-KFA / 190T-KFA / 215T-KFA

Tools Needed:

- Phillips Head Screw Driver
- 8 mm open end wrench
- 19 mm open end wrench

Tip: Be sure to remove the axle from the side of 

the Styrofoam packaging.
Tip: Use a power screwdriver and locking wrench 

for easier assembly. 

Front Handle

Axle

Rear Handle

Wheel Support Frame

50 mm Screws (4)

30 mm Screws (4)

8 mm Nuts (8)

 

 

 

 

Wheels (2)

Axle Nuts (2)

Spacers (2)

Spare Drain Plug (1)

Assembly Instructions

Models: 135T-KFA / 175T-KFA / 190T-KFA / 215T-KFA

1. Insert axle through holes in wheel support. 
2. Slide spacer onto axle.
3. Slide wheel onto axle and hold in place with the axle nuts. 

(See Figure 1).

4. Place heater on wheel support and line up  holes on the fuel 

tank lip.

5. Attach front handle with (2) long screws  

(50 mm) and (2) nuts through the second hole from the front 

on both sides of the tank lip and wheel support frame and 

tighten firmly.

6. Insert (2) short screws (30 mm) through the first hole from the 

front in the tank lip and tighten firmly. Make certain all (4) 

screws are secure. 

7. Attach rear handle with (2) long screws  

(50 mm) and (2) nuts through the second hole from the rear 

of the heater on either side. (See Figure 2)

8. Tilt the heater up gently so it is resting on the front handle.

NOTE: DO NOT do this if there is fuel in the tank.

9. Remove the wheels to secure the second set of screws 

through the rear handle.

10. Secure the rear handle with (2) short screws  (30 mm) and 

(2) nuts and tighten firmly

11. Replace wheels and tighten with the wheel nuts.
12. Tilt heater back down onto wheels and check all screws and 

nuts to make sure they are secure.

 

Figure 1

Axle

Axle Nut

Spacer

Tire

Wheel Support Frame

 

 

Figure 2

Summary of Contents for Remington REM-135T-KFA-O















Reviews: