background image

 
_______________________________________________________________________________ 

 

3 of 19 

Navod obsl OR 50(F)_2006-08-01_EN.doc 

 

 

 

1999 

 Pilous pásové pily spol.s r.o. 
 Vranovská 5 
 614 00 BRNO 
 TSCHECHISCHE REPUBLIK   

 

All rights, particularly the right to make copies of, to distribute and translate this 
instruction manual, are reserved. 
No part of this instruction manual may in any form (printing, microfilm or others) be 
reproduced or stored, processed, copied or distributed by using electronic systems 
without permission of PILOUS. 
 

 

Letter of Guarantee – Service 

 

The Letter of Guarantee is a separate annex to the instruction manual. 
Guarantee period – see Letter of Guarantee 
 

Conditions for Maintenance of Claims under Guarantee 

 

Use and attendance of the machine in conformity with the instruction manual. 
Connection of the machine to voltage corresponding to that mentioned in the instruction 
manual 

 

The guarantee does not apply to: 

 
Violent and mechanical damage of the machine caused by interference of the user or 
other persons. 
Unavoidable event (natural disaster) 
Damage of machine during transport 
Storage or installation of machine in humid, chemical or any other unsuitable environment 
 

Any claims concerning guarantee and after-guarantee repairs should be sent by fax, 
post or phone to the address: refer to the Letter of Guarantee. 
 
Instruction for the User: 

 
The Seller is obliged to hand over to the User the Letter of Guarantee immediately when 
the product is being purchased. The Letter of Guarantee must be carefully and legibly 
completed and provided with the Seller’s stamp, signature and data of sale. 
The Seller is obliged to inform the Buyer about the use and handling the product. 
 

Data Necessary for Claiming Guarantee (After-Guarantee) Repair 
 
Machine type 
Number of Letter of Guarantee (identical with serial number)  
Date of issue of Letter of Guarantee 

 

 

 
 

C

 

Summary of Contents for FORESTOR OR 50





















Reviews: