Pilot RC EDGE540 User Manual Download Page 3

Page: 3 / 22

Included Hardware:

• Complete air frame with all basic accessories (such as carbon

fibre main

undercarriage, tail-gear assembly and wing-tube as well as fibreglass control

horns and wheel pants)

• Pre

-installed hinges and pre-mounted canopy

• Wheels, axels and wheel pants

• Pushrods with ball links

• Matching plastic spinner

• Wing bags

• Servo extension wires

Propeller: 15x8E

Also requires all the usual accessories such as transmitter, receiver, propeller,

batteries, powerbox, extension leads and possibly other small accessories.

Engine Option 1 : Gasoline

Transmitters and Receivers

Gasoline engine - 20cc ) (for example DLE-20RA)

Servos (5pcs) (for example Pilot-RC PY-20AL)

Batteries of your choice - RX and / or Ignition

Engine Option 2: Electric

Transmitters and Receivers

Servos (4pcs) (for example Pilot-RC PY-20AL)

Electric motor (Pilot-RC CC20/400KV motor)

ESC (100A )

Batteries of your choice (3300-4500mah 6S 22.2V 35C lipo battery)

Required Hardware:

Other Accessories Needed To Complete:

• Epoxy Adhesives

•

Cyanocrylate adhesives

• X

-Acto and Saw knives

• Sandpaper

• Thread lock

• Aircraft stand or support

• Drill, screw drivers,

allen keys, wrench set, pliers, etc

Summary of Contents for EDGE540























Search results

Summary of Contents for EDGE540

Reviews:

Related manuals for EDGE540

Brands by name

Popular brands

Pilot RC EDGE540, User Manual

Search results

Summary of Contents for EDGE540

Reviews:

Related manuals for EDGE540

Brands by name

Popular brands