2. Place rear axle into stroller frame. You should
hear snap. Ensure that the
brake is facing the rear.
Fig 2
3. Place the rear wheels into axle pins. When you adjusted properly you should hear
"click". Make this action for the second front whee
l too.
IMPORTANT:
Inflate tires of rear wheels max. 35 PSI (240 KPa)
/ (2.4 BAR), be
careful not to exceed the specified value.
Fig 3
4. Place the front swivel wheels into front housing
. When you adjusted properly
you should hear "click". Make this action for the second front wheel too.
WARNING:
Before using the stroller, make sure that the wheel
s are well
secured to the structure.
Fig 4
5. The stroller is equipped with front swivel/fixed
wheels.
It is suggested to use the fixed wheels on particul
arly uneven grounds. The wheels
in swivel mode instead, can be used to improve the stroller’s handling on regular
road surfaces.
To lock the front swivel wheels, press down the locking button on the front yoke. To
release the locking device of the front fixed wheel
s, press again the locking button
with your foot. Regardless of the position in which
the wheel is located, they will
lock in straight position.
Fig 5
WARNING:
Both wheels must always be locked or released to swivel at the same time.
WARNING:
Before using the stroller, make sure that the wheel
s are well secured to the structure.
ASSEMBLY OF THE SEAT: STROLLER CONFIGURATION
6. Put the seat into the corresponding holes on the
construction of a stroller, as
shown in Figure 6, you should hear a click fuses.
WARNING:
Make sure the seat is installed properly by pulling
it upward.
Fig 6
WARNING:
The seat can be placed on the chassis only so that the child is seated in the driving direction.
If you want to remove the seat, press two fuses located on both of the sides of the joint at the bottom of the
seat and pull the seat up. These actions do not make when a baby is in the seat.
WARNING:
Do not remove the seat from the stroller when the child is inside of it.
CANOPY
7. A canopy can be installed on the stroller.
The seat features two joints positioned on the sides of the
backrest that allow the securing of the canopy.
To secure the canopy, introduce the fastening syste
m into
the joints as shown in Fig 7.
Then, secure the fabric part to the canopy using th
e zip
located on the seat frame, around the backrest.
WARNING: The canopy must be anchored to both sides
of the stroller. Make sure it is secured properly.
Fig 7
Fig 7.1
Oversize zippered canopy extension offers full cove
rage keeping your child protected.
To remove the canopy, open the zip of the canopy’s fabric part completely and press the buttons locate
d
inside the canopy’s joints then pull the canopy upward.
To adjust the canopy, pull and/or push it centrally, Fig 7.1.
REMOVABLE BUMPER BAR
8. The stroller is equipped with removable bumper bar.
To fix the bumper bar, insert it into holes on the
construction, as shown in
Fig 8, you should here the click.
To remove it, press the buttons located inside on t
he both sides of the
bumper bar.
To position and remove the child, unhook the bar fr
om one side only.
Fig 8
WARNING:
Always fasten the safety belts. The bar IS NOT a d
evice to retain the child.
WARNING:
The bar must not be used to lift the product with the child inside of it.
SEAT ADJUSTMENTS
9. Once the seat is assembled on the frame, it can be adjusted in three different positions.
The seat can be adjusted by pressing the button in
the rear part of the seat, see Fig 9.
Fig 9
15-0229_Navod_Gmini_Grand.indd 23
12.3.2015 11:00:23
15-0658_Navod_Gmini_Grand.indd 23
3.7.2015 10:26:49