background image

 

 

5 Installation 

P-63x Nanopositioner 

PZ247E 

Version: 1.1.0 

19 

 

You have provided a suitable surface for fixing the P-63x: 

 

The surface has four suitable threaded holes for M2.5 screws. Refer to 

"Dimensions" (p. 35) for the required position and depth of the holes. 

 

The surface flatness is ≤20 µm. 

 

For applications with large temperature fluctuations: The surface should have the 

same thermal expansion properties as the P-63x (e.g., surface made of aluminum). 

Tools and accessories 

 

4 M2.5x20 screws (p. 11) 

 

Hex key AF 2 (p. 11) 

Mounting the P-63x 

1.

 

Align the P-63x on the underlying surface so that the corresponding mounting holes in 

the base body (see figure) and the surface are in line. 

2.

 

Fix the P-63x with the screws: 
a)

 

Insert a screw into each hole. 

b)

 

Tighten the screws. Pay attention to the specified torque range (p. 36) while doing 

so. 

3.

 

Check that the P-63x is sitting firmly on the surface. 

 

 

5.4

 

Fixing the Load 

 

NOTICE 

 

Mechanical overload of the motion platform! 

High torques during fastening of the load as well as heavy loads can overload the motion 

platform of the P-63x. Mechanical overload can cause damage to the piezo actuators, sensors, 

and flexures of the P-63x and lead to loss of accuracy. 

 

Avoid torques >0.5 Nm on the motion platform. 

 

Do 

not

 exceed the maximum permissible loads according to the specifications (p. 33)

 

Hold the load and adhere to the specified torque range (p. 36) when tightening (or 

loosening) the screws. 

  

Summary of Contents for P-63 Series














































Reviews:

Related manuals for P-63 Series