background image

Performer User's Manual                  PHONIC CORPORATION

page 10

PHONIC CORPORATION                   Performer User's Manual        

page 11

Wireless Setup

4) System One:

This  configuration  uses  a  Phonic  wireless  microphone 

with  three  Performer  active  speakers.  You  can  use  a 

Phonic UHF or VHF wireless microphone with wireless 

module to transmit to the speakers. Set the WIRELESS/

WIRELESS MIC Switch out (up) on the back of Speaker 

1

, and set it in (down) on Speakers 

2

 and 

3

. Speaker 

1

  is  fitted  with  two  wireless  modules  installed  in  the 

two  compartments  on  the  top  of  the  speaker.  One 

compartment  has  the  matched-frequency  wireless 

module for the UHF or VHF wireless microphone. The 

other compartment is fitted with a Wireless Transmitter 

Module  (WM  30)  for  re-transmitting  the  source  signal 

to  other  wireless-enabled  Performer  active  speakers. 

Speaker 

2

 is fitted with a Wireless Transmitter/Receiver 

Module  (WM  50)  for  receiving  the  source  signal 

transmission  from  Speaker 

1

  and  re-transmitting  it  to 

Speaker 

3

,  which  is  fitted  with  a  Wireless  Receiver 

Module  (WM  40).  In  this  way  you  have  a  completely 

wireless system with all the speakers receiving the same 

signal from the wireless microphone. (To install wireless 

modules please refer to the instructions on page 15.)

Note:

 The  Wireless Transmitter  modules  (WM  30  and  WM  50) 

have a range of up to 100 feet (30 meters). If Speakers 

2

 and 

3

 

are both within that range of distance from Speaker 

1

, then they 

only need to be fitted with a Wireless Receiver Module (WM 40).

Related Products: UM 11, UM 22, VM 11, VM 22, WM 

30, WM 40, WM 50

VHF / UHF Wireless 

Microphone

Performer Speaker

SYSTEM ONE

Performer Speaker

1

3

2

up to 100 feet 

(30 meters)

up to 100 feet 

(30 meters)

up to 300 feet 

(100 meters)

Performer Speaker

2.4 GHz Transmitter (WM30)

2.4 GHz Receiver (WM400)

2.4 GHz Transmitter /
Receiver (WM50)

VHF / UHF Receiver 

Summary of Contents for performer A210





















Reviews: