background image

Performer User's Manual                  PHONIC CORPORATION

page 12

PHONIC CORPORATION                   Performer User's Manual        

page 13

5)  System Two (Stereo):

This  configuration  uses  a  Phonic  wireless 

microphone and mixer with Stand Alone Wireless 

Transmitter  Module  (WM  60)  transmitting  the 

source  signals  to  five  "virtually"  daisy  chained 

Performer active speakers. You can use a Phonic 

VHF  or  UHF  wireless  microphone  with  wireless 

module  to  transmit  to  the  speakers.  Set  the 

WIRELESS/WIRELESS MIC Switch in (down) on 

the back of all the speakers. Speaker 

1

 has two 

wireless modules installed in the two compartments 

on  the  top  of  the  speaker.  One  compartment  is 

fitted with the matched-frequency wireless module 

for  the  UHF  or  VHF  wireless  microphone.  The 

other  compartment  is  fitted  with  a  Transmitter 

&  Receiver  Module  (WM  50)  for  receiving  the 

transmission  from  the  Stand  Alone  Wireless 

Transmitter  Module  (WM  60)  and  re-transmitting 

it  to  the  next  speakers  in  the  series.  Speaker 

1

re-transmits the VHF / UHF wireless microphone 

signal to Speaker 

2

, and the wireless microphone 

and mixer signals to Speaker 

3

. Speakers 

2

 and 

3

  both  are  fitted  with  a  Transmitter  &  Receiver 

Module (WM 50) and they re-transmit the signals 

to Speakers 

4

 and 

5

, respectively. Speakers 

4

and 

5

  each  are  fitted  with  a  Wireless  Receiver 

Module (WM 40) to receive the transmission from 

Speakers 

2

 and 

3

, respectively. This setup allows 

all  the  speakers  to  instantly  receive  the  wireless 

microphone and mixer signals. You also are able to 

play the mixer signals in stereo image because the 

WM 60 auto-detects left- and right-side speakers. 

(To  install  wireless  modules  please  refer  to  the 

instructions on page 15.)

Related Products: UM 11, UM 22, VM 11, VM 22, 

WM 30, WM 40, WM 50, WM 60

VHF / UHF 

Wireless Microphone

Mixer

L

R

Performer Speaker

SYSTEM TWO ( STEREO )

Performer Speaker

Performer Speaker

Performer Speaker

Performer Speaker

1

3

5

4

2

up to 100 feet 

(30 meters)

up to 100 feet 

(30 meters)

up to 100 feet 

(30 meters)

up to 100 feet 

(30 meters)

up to 100 feet 

(30 meters)

WM60

2.4 GHz Transmitter (WM30)

2.4 GHz Receiver (WM400)

2.4 GHz Transmitter /
Receiver (WM50)

VHF / UHF Receiver 

Summary of Contents for performer A210





















Reviews: