background image

1. 

Read  these  instructions  before 

operating 

this 

apparatus.

2.

  Keep these instructions for future reference.

3.  H

eed all warnings to ensure safe operation.

4. 

Follow all instructions provided in this document.

5.  Do not use this apparatus near 

water

 or in locations 

where condensation may occ

ur.

6.  Clean 

only with

 d

ry 

cloth. Do not use aerosol or 

liquid 

cleaners. Unplug this apparatus before cleaning.

7.  Do not block 

any 

of the ventilation 

openings. 

Install 

in accordance with the manufacturer

’s instructions.

8.  Do not install near 

any 

heat sources such as radiators, 

heat 

registers, 

stoves, or other apparatus 

(including 

.

9.

  Do not defeat the 

safety 

purpose of the polarized or 

grounding-type plug. 

A polarized 

plug 

has 

two 

blades 

with one wider than the other

. A 

grounding type plug 

has 

two 

blades and a third 

grounding

 p

rong. 

The 

wide

 

blade or the third 

prong 

is provided for 

your safety

. If 

the provided 

plug 

does not   into 

your 

outlet, consult 

an electrician for replacement of the obsolete outlet.

10. 

Protect  the 

power 

cord  from 

being  walked 

on  or 

pinched 

particularly 

at 

plug, 

convenience receptacles, 

and the point where they exit from the apparatus.

11

Only 

use 

attachments/accessories 

 b

the 

manufacturer.

12. 

Use 

only  with 

a  cart,  stand,  tripod,  bracket,  or 

table 

  b

the  manufacturer,  or  sold 

with

 

the  apparatus.  When  a  cart  is  used,  use  caution 

when  moving 

the 

cart/apparatus

 

combination to avoid 

injury 

from tip

-

over.

13. 

Unplu

g this apparatus during lighting 

storms  or

  w

hen  unused  for  lon

periods of time.

14. 

Refer  all 

servicing 

to 

  service    personnel. 

Servicing 

is 

required when

 the apparatus has been 

damaged 

in 

any way

, such as 

power-supply 

cord or 

plug 

is 

damaged, liquid 

has been spilled or objects 

have  fallen  into  the  apparatus,  the  apparatus  has 
been exposed to rain or moisture, does not operate 

normally

, or has been dropped.

IMPOrTaNT SafETY INSTruCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED PERSONNEL

The 

lightning 

flash 

with  arrowhead  symbol,  w

ithin  an 

equilateral  triangle, 

is  intended  to  alert  the  user  to  the 

presence  of  uninsulated  “

dangerous  voltage

” 

within 

the 

product’

 

magnitude to constitute a risk of electric shock to person

s.

The exclamation point 

within 

an 

equilatera

triangle 

is i

n-

tended to alert the user to the presence of important operat

-

ing 

and maintenance 

(servicing

) instructions in the literature 

accompanying the applianc

e.

WarNING: 

To reduce the risk of 

 or electric shock, do 

not expose this apparatus to rain or moisture.

CauTION: 

Use of controls or adjustments or performance 

of  procedures  other  than  those 

  m

ay 

result  in 

hazardous radiation exposure.

The apparatus shall not be exposed to 

dripping

 or 

splashing 

and that no objects 

 

with liquids, 

such as vases, 

shall be placed on the apparatus. The MAINS 

plug

 is used as the disconnect device, the disconnect device shall 

remain readily operable. 

Warning

: the user shall not place this apparatus in the 

 area 

during 

the operation so that the mains 

switch 

can be easily accessible. 

CauTION

rISK Of ElECTrIC ShOCK

DO NOT OPEN

Summary of Contents for ICON300

























Reviews: