background image

Instruction manual

1. Read this instruction manual carefully.
2. Keep this instruction manual safe.
3. Observe all warnings.
4. Observe all instructions.
5. CAUTION: To avoid fires and electric shocks, this system may not be exposed to rain and humidity. Do not use this 
device near waters.
6. Clean only with a dry cloth. 
7. Do not cover any air vents.
8. Do not place this device close to heat sources like radiators, hot air dampers, ovens or other units (including ampli-
fiers) which  release heat.
9. Do not invalidate the safety function of the inverse-polarity protection plug or the safety plug. A plug with inverse-polarity 
protection has two pins, from which one is wider than the other (only for USA/Canada). A safety plug has two pins and 
one ground pole (only for USA/Canada). The wide pin resp. the third pole are intended for your safety. If the included 
plug does not fit in your  socket, the socket is obsolete and has to be replaced by an electrician.
10. Pass the power cable in a way that nobody can step onto it or that it can be jammed. This is to apply especially for 
plugs, sockets and the place where the cable comes out of the device.
11. Only use equipment and products specified by Phoenix Professional  Audio GmbH.
12. Maintenance operations should only be done by qualified maintenance staff. The device has always to be maintained 
if it has been damaged in any way, such as power cable or power plug is damaged, liquids have been spilt on the device 
or objects have fallen into the device, if the device has been exposed to rain or humidity, if it does not operate as usual 
or if it fell down.

The exclamation mark in a triangle shall advise the user of the existence of important 

operation- and maintenance instructions in this manual.

The symbol consisting of a flash with an arrowhead shall advise the user of the 

existence of  non-insulated, dangerous voltages within the housing, which can be 

strong enough to get an electric shock.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE 

COVER. ONLY USE QUALIFIED STAFF FOR ALL MAINTENANCE WORKS.

Important safety precautions and symbol explanation

EXPLANATION OF THE GRAPHIC SYMBOLS

Summary of Contents for DigiVoice-110.8 DSP2





















Reviews: