background image

                                                         Phoenix 2700 DH 

         July 2018 

 

14 

 

16.  Motor Switch Safety Feature

 

1.

 

Should the main ON/OFF switch be turned to OFF while the motor 
switch is in FWD position, the motor must be reset to resume operation.

 

2.

 

To reset the motor, turn the main ON/OFF switch to the ON position, 
then turn the motor switch to OFF or “0” positon, then to FWD when 
ready to operate.

 

 

17. Heat Sensor Safety Feature

 

1.

 

Should the heat senor located on the front side of the bottom heat roller 
become blocked, the motor and heater will stop

 

2.

 

The Power light will flash, and you will hear three fast repeating audible beeps

 

3.

 

Clear away any paper or film between the sensor and the roller from 
front of the machine

 

 

               

 
 

 
                 

 

4.

 

To reset the sensor, turn the motor Forward/Reverse switch to neutral or 
“O” positon and the main ON/OFF switch to OFF, then back to ON

 

a.

 

You should hear three slow beeps indicating the sensor has been cleared

 

 

18. Loading Film rolls 

 

1.

 

Determine whether your film is on 1” or 2 ¼” diameter cores 

2.

 

Select to use the 1” core clip or 2 ¼” core adaptor for your film 

a.

 

1” core clip is mounted in the middle of each supply shaft 

b.

 

If using 1” core film, loosen the two (2) adaptor screws on each 2 ¼” core 
adaptor and slide them off the film shafts 

 

 

                                                     

 

Supply shaft 

1” core clip 

Top Roller 

Heat Sensor 

Bottom Idler bar 

Summary of Contents for 2700-DH
























Reviews: