background image

3

SAFETY PRECAUTIONS

This label may appear on the bottom of the unit due to space limitations.

The lightning flash with an arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended
to alert the user to presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

Attention: Installation should be performed by qualified
service personnel only in accordance with the National
Electrical Code or applicable local codes.

Power Disconnect. Units with or without ON-OFF switches
have power supplied to the unit whenever the power cord is
inserted into the power source; however, the unit is operational
only when the ON-OFF switch is in the ON position. The
power cord is the main power disconnect for all units.

Battery Replacement Caution
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer's instructions.

External Power Supplies
Use only the Recommended Power Supplies. Power supplies
must comply with the requirements of the latest version of IEC
65/VDE 0860. Substitutions may damage the unit or cause a fire
or shock hazard.

SECURITE

En raison de limitation de place, cette étiquette peut être placée sur le
dessous de l'appareil.

L'éclair fléché dans un triangle équilatéral, avertit l'utilisateur de
la présence d'une "tension dangereuse" non isolée à l'intérieur
de l'appareil et d'une valeur suffisante pour constituer un risque
d'électrocution.

Le point d'exclamation contenu dans un triangle équilatéral,
avertit l'utilisateur de la présence, dans la documentation qui
accompagne l'appareil, de consignes d'utilisation et de
maintenance importantes.

Attention: L'installation doit être effectuée uniquement par du
personnel de service qualifié conformément à la réglementation
du Code Electrique National ou à la réglementation locale.

Disjonction de l'alimentation. Les appareils avec ou sans
commutateurs ON-OFF sont alimentés à chaque fois que le
cordon d'alimentation est branché à la source d'alimentation;
toutefois, les appareils disposant de commutateurs ON-OFF ne
fonctionnnent que lorsque le commutateur ON-OFF est sur la
position ON. Le cordon d'alimentation est la disjonction
d'alimentation principale pour tous les appareils.

Changement de piles - Attention!
Danger d'explosion si le changement de pile n'est pas effectué
correctement. N'utilisez que des piles du même type ou d'un
type équivalent recommandé par le fabricant.Veuillez respecter
les consignes du fabricant lorsque vous jetez les piles usagées.

Sources d'alimentation extérieures
Utiliser uniquement les sources d'alimentation recommandées.
Les sources d'alimentation doivent être conformes aux
réglementations de la dernière version IEC 65/VDE 0860.Toute
modification peut endommager l'appareil ou provoquer un
incendie ou un choc électrique.

Caution: To reduce the risk of electrical shock, 
do not open covers. No user serviceable parts inside.  
Refer servicing to qualified service personnel

R I S K   O F   E L E C T R I C

S H O C K .   D O   N O T   O P E N !  

C A U T I O N

Danger: Pour ‚éviter tout risque d'électrocution, ne pas
ouvrir le boîtier.  Il n'y a pas de pièces remplaçables à
l'intérieur.  Pour toute révision, s'adresser à un 
technicien spécialisé.

R I S Q U E   D E   C H O C   E L E C T R I Q U E .

N E   P A S   O U V R I R .  

A T T E N T I O N

Warning:To prevent fire or shock hazard, do not
expose units not specifically designed for
outdoor use to rain or moisture.

Attention: Pour éviter le risque
d'électrocution ou d'incendie, ne pas exposer
à la pluie ou à l'humidité un appareil non
conçu pour une utilisation extérieure.

Summary of Contents for VidQuad Color Video Processors TC8278

















Reviews: