background image

English

7

General Information

Supplied accessories

– 2 speaker boxes including 2 speaker cables
– remote control (with 1 x CR2025 battery)
– stand

– mounting kit

– 1 X certified AC/DC adapter (Input: 100-

240V ~ 50-60Hz 0.8A MAX., Output:14V

 1.8A)

Environmental Information

All unnecessar y packaging has been omitted. We

have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).

Your system consists of materials which can be

recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.

Safety Information

Place the system on a flat, hard and stable
surface.

Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system.  Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.

The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.

Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.

No naked flame sources, such as lighted candles,
should be placed on the apparatus.

No objects filled with liquids, such as vases, shall
be placed on the apparatus.

Install this unit near the AC outlet and where the
AC power plug can be reached easily.

If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens of the disc
unit inside the system. Should this occur, the CD
player would not operate normally. Leave the
power on for about one hour with no disc in the
system until normal playback is possible.

The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.

When the system is switched to Standby
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the AC
power plug from the wall socket.

Disposal of  your old product

Your product is designed and
manufactured with high quality materials
and components, which can be recycled
and reused.

When this crossed-
out wheeled bin
symbol is attached to
a product it means
the product is
covered by the
European Directive
2002/96/EC

Please inform yourself about the local
separate collection system for electrical
and electronic products.

Please act according to your local rules
and do not dispose of your old products
with your normal household waste. The
correct disposal of your old product will
help prevent potential negative
consequences for the environment and
human health.

P001-P030_MCB275_05_Eng

2007.6.13, 10:27

7

Summary of Contents for MCB27































Reviews: